Kit5000_GB-A
The product you have acquired is integrated into an industrial door. Its being put on the European Union market
implies EC marking by a certified agency, under the liabilities of the manufacturer and/or installer of the door.
The design, manufacture and installation of an industrial door must respect the essential requirements of health and
safety determined by the following European directives:
NM2480CE/J
1 – GENERAL INFORMATION
1.1. Regulations & Obligations
The product you have acquired is integrated into an industrial door. Its being put on the European
Union market implies EC marking by a certified agency, under the liabilities of the manufacturer
and / or installer of the door.
The design, manufacture and installation of an industrial door must respect the essential
requirements of health and safety determined by the following European directives:
European Directives
Manual door
Motorised door
Construction Products Directive 89/106/EEC
X
X
Low Voltage Directive 2006/95/CE
X
Electro-magnetic Compatibility Directive 2004/108/CE
X
Machines and Working Equipment Directive 2006/42/EC
X
The proof of conformity to the regulation texts, mentioned above, is obtained by the respect of the
standard reference detailed by the standard of product
NF EN 13241-1
. - Industrial, Commercial
and Garage Doors (Part 1: products without fire and smoke proofing characteristics)
Terminology standard
Safety standard
Environmental
standard
Electrical and DCEM
standard
EN 12433-1
Types of doors
EN 12604
Mechanical aspects
EN 12424
Resistance to wind
EN 60204-1
Machine electrical safety
EN 12433-2
Components of doors
EN 12605
Test methods
EN 12444
Tests and calculations
EN 61000-6-2 (DCEM)
Immunity to industrial
environment
EN 12453
Safety of use
EN12425
Water penetration
EN 61000-6-3 (DCEM)
Harmonic measure emission
EN 12445
Test methods
EN 12489
Test methods
EN 61000-6-4
Industrial environment
emission
EN 12978
Safety devices
EN 12426
Permeability to air
EN 12635
Installation and use
EN 12427
Test methods
EN 12428
Thermal transmission
FERMOD has taken the standards that apply to the supplied products into consideration.
- 22 -
1.2 – Liabilities
1 – The manufacturer of the door, the installer and the user must observe the safety rules (collective protection, individual
protection) applicable during transport, assembly, use, and discarding of the door or its components.
2 – The liability of the user may be engaged in circumstances that are not marginal. Thus, the user must scrupulously
comply with the recommendations for storage, assembly, use, maintenance, health and safety, use-by date, etc. supplied
by the manufacturer.
Likewise, where the producer be held liable for the non-conformity of the product, the user may also share the liability,
insofar as he has not, from his side, checked this conformity, even if the product in question is administratively in
conformity. The user is also held liable if he himself increases the fault in the product.
The proof of conformity to the regulation texts, mentioned above, is obtained by the respect of the standard reference
detailed by the standard of product
NF EN 13241-1
: Industrial, Commercial and Garage Doors (Part 1: products without
fire and smoke proofing characteristics).
FERMOD has taken the standards that apply to the supplied products into consideration.
NM2480CE/J
1 – GENERAL INFORMATION
1.1. Regulations & Obligations
The product you have acquired is integrated into an industrial door. Its being put on the European
Union market implies EC marking by a certified agency, under the liabilities of the manufacturer
and / or installer of the door.
The design, manufacture and installation of an industrial door must respect the essential
requirements of health and safety determined by the following European directives:
European Directives
Manual door
Motorised door
Construction Products Directive 89/106/EEC
X
X
Low Voltage Directive 2006/95/CE
X
Electro-magnetic Compatibility Directive 2004/108/CE
X
Machines and Working Equipment Directive 2006/42/EC
X
The proof of conformity to the regulation texts, mentioned above, is obtained by the respect of the
standard reference detailed by the standard of product
NF EN 13241-1
. - Industrial, Commercial
and Garage Doors (Part 1: products without fire and smoke proofing characteristics)
Terminology standard
Safety standard
Environmental
standard
Electrical and DCEM
standard
EN 12433-1
Types of doors
EN 12604
Mechanical aspects
EN 12424
Resistance to wind
EN 60204-1
Machine electrical safety
EN 12433-2
Components of doors
EN 12605
Test methods
EN 12444
Tests and calculations
EN 61000-6-2 (DCEM)
Immunity to industrial
environment
EN 12453
Safety of use
EN12425
Water penetration
EN 61000-6-3 (DCEM)
Harmonic measure emission
EN 12445
Test methods
EN 12489
Test methods
EN 61000-6-4
Industrial environment
emission
EN 12978
Safety devices
EN 12426
Permeability to air
EN 12635
Installation and use
EN 12427
Test methods
EN 12428
Thermal transmission
FERMOD has taken the standards that apply to the supplied products into consideration.
- 22 -
1.2 – Liabilities
1 – The manufacturer of the door, the installer and the user must observe the safety rules (collective protection, individual
protection) applicable during transport, assembly, use, and discarding of the door or its components.
2 – The liability of the user may be engaged in circumstances that are not marginal. Thus, the user must scrupulously
comply with the recommendations for storage, assembly, use, maintenance, health and safety, use-by date, etc. supplied
by the manufacturer.
Likewise, where the producer be held liable for the non-conformity of the product, the user may also share the liability,
insofar as he has not, from his side, checked this conformity, even if the product in question is administratively in
conformity. The user is also held liable if he himself increases the fault in the product.
REGULATIONS & OBLIGATIONS
1.1
- 3 -
LIABILITIES
1.2
1 –
The manufacturer of the door, the installer and the user must observe the safety rules (collective protection, individual
protection) applicable during transport, assembly, use, and discarding of the door or its components.
2 –
The liability of the user may be engaged in circumstances that are not marginal. Thus, the user must scrupulously
comply with the recommendations for storage, assembly, use, maintenance, health and safety, use-by date, etc... supplied
by the manufacturer.
Likewise, where the producer be held liable for the non-conformity of the product, the user may also share the liability,
insofar as he has not, from his side, checked this conformity, even if the product in question is administratively in
conformity. The user is also held liable if he himself increases the fault in the product.
The liability of the manufacturer can be reduced or eliminated, taking all the circumstances into consideration, when the
damage is caused jointly by the product, and by the fault of the victim or a person for whom the victim is responsible
(D. general safety of products 92/59/EEC et D. liability from the fact of faulty products 85/374/EEC).
3 –
Safety devices fitted to the doors are not intended to prevent any wilful act of the operator or persons nearby
(EN12604 §4.1.2).
4 –
The choice of options follows the type of door installed. It is the manufacturer’s responsibility to ensure the compatibility
of accessories according to the characteristics of the door and the conditions of use
(EN12604 § 4.2.1).
1 - GENERAL INFORMATIONS
