Close the engine compartment lid, checking that
it closes correctly and is flush with the
bumper.
If the engine compartment lid closes incorrectly
or is not flush with the surrounding bodywork,
adjust the engine compartment lid striker
plate by adjusting the four respective fastener
screws.
Replacing the engine compartment lid release Bowden cable
Fastening passenger compartment air intake tray Nut / Screw
7.5 Nm
B
Fastening engine compartment lid release handle Screw
2.6 Nm
C
Tightening torque
Nm
Class
The engine compartment lid release dual Bowden cable is located in the engine compartment, under the
cosmetic shields.
FROM Assembly No. 86054, the dual Bowden cable with emergency release mechanism has been replaced
by a single Bowden cable located on the left hand side of the engine compartment. As a result,
emergency lid release is no longer possible.
Remove the engine compartment cosmetic shields (
E3.13
).
Remove the windscreen wiper linkage (
E3.09
).
Replace the engine compartment lid lock (
E5.14
).
Detach the Bowden cable only.
Detach the indicated clips fastening the Bowden
cable
(A)
on the left hand side of the engine
compartment.
Note that not all the fastener clips are shown in
the image aside.
Summary of Contents for California
