Cut the sealant to a depth no greater than 25
mm.
Use specific pneumatic cutters to cut the sealant
around the entire perimeter of the rear screen
from inside the passenger compartment.
Use suction cup handles
(1)
to remove the rear
screen
(E)
from its seat.
This operation must be carried out with the
assistance of another operator.
Apply strips of adhesive tape to the bodywork,
around the perimeter of the rear screen seat.
Take care not to damage the bodywork;
Remove residual sealant with the (Excalibur
pneumatic cutter with ESM - 519 short blade)
(A)
.
Clean the rear screen mating surface on the
Tonneau Cover with heptane, removing all
residue of adhesive or dust.
The rear screen is supplied as a spare part
with primer already applied. The screen
must be used within 3 months of the date
application of the primer. The primer must
be reactivated if more than 3 months
have elapsed since application.
The primer application date is printed on the
rear screen.
The adhesive must be applied to the rear
screen within 15 minutes of reactivating
the primer.
The image aside shows the rear screen with the
zone
(2)
printed with the application date of
the primer and the bead of adhesive
(3)
with
overlapped joint in the position indicated.
Summary of Contents for California
