Working from the front right wheel bay, fit the
gear oil heat exchanger
(A)
in the relative
mounting bracket and fasten by tightening the
four nuts indicated.
Tightening torque
Nm
Class
Nut 9
Nm
B
Fasten the front gear oil pipe to the mounting
bracket, fitting the clamp
(8)
.
Fasten the right injection cable to the chassis
and to the mounting bracket, fastening the
two clamps
(1)
.
Take care not to contaminate the two
systems.
Remove the plugs from the oil pipes and the
respective orifices on the heat exchanger;
keeping the pipes in their original positions as
noted during removal, fit the oil pipes and
fasten with the pipe unions
(7)
, after replacing
the four seals.
Tightening torque
Nm
Class
Pipe union
50 Nm
A
Remove the plugs from the water pipes and the
respective orifices on the heat exchanger;
keeping the pipes in their original positions as
noted during removal, fit the water pipes and
fasten with the pipe unions
(6)
, after replacing
the four seals.
Tightening torque
Nm
Class
Pipe union
50 Nm
A
Attach the water pipes to the clamp, fastening
the assembly with the screw indicated.
Clean thoroughly to remove all residual liquid and remove the absorbent paper used to protect the ECU,
cables, wiring harnesses and connectors.
Summary of Contents for California
