After loosening or removal, the Caillau Visa hose clamps must be replaced with Mikalor worm drive
hose clamps, following the instructions given in Technical Information 2054 of December 2012.
Remove the front flat undertray section (
E3.12
).
Working from under the vehicle, on the right-
hand side of the radiator, loosen the clamps
(1)
fastening the delivery and return pipes
(2)
.
Detach the pipes
(2)
from the radiator.
Pour the fluid drained from the system into a
container and seal it. DO NOT DISPOSE
OF USED FLUID IN THE
ENVIRONMENT.
Let the coolant drain completely.
Filling the cooling system
After loosening or removal, the Caillau Visa hose clamps must be replaced with Mikalor worm drive
hose clamps, following the instructions given in Technical Information 2054 of December 2012.
CAUTION
The fluid in the engine coolant system may be very hot.
Hot engine coolant may cause severe burns.
ALWAYS WAIT FOR THE SYSTEM TO COOL BEFORE STARTING ANY WORK.
Check that all the connection sleeve clamps are tight.
Static filling (engine off) (ONLY for vehicles WITHOUT Single oil heat exchanger)
Cap - front cover
M12x1.25x12 plug
30 Nm
B
Water-oil pipes - gear oil heat exchanger
Pipe union
50 Nm
A
Tightening torque
Nm
Class
Remove the engine compartment cosmetic shields (
E3.13
).
Remove the front wheelhouses (
E3.05
).
Remove the rear right hand element.
Summary of Contents for California
