If the value measured is incorrect, adjust as
follows.
Loosen the screw
(4)
by a few thread turns.
Holding the adjuster dowel
(10)
still to prevent it
from turning, loosen the nut
(9)
by a few
thread turns.
Manually move the quarterlight into the correct
position.
Once adjustment is complete, tighten the screw
(4)
and, holding the adjuster dowel
(10)
still to
prevent it from turning, tighten the nut
(9)
.
Tightening torque
Nm
Class
Screw 9.5
Nm
B
Nut 9.5
Nm
B
Apply two strips of white adhesive tape in the
positions indicated in the photo aside.
With the quarterlight raised to its travel limit,
mark the strips of tape with a marker pen as
shown in the photo.
Use the relative button to lower the quarterlight
and check that it intrudes into the Rear Roof
seal, at both reference points
(6)
, by
4 mm
.
Check that the quarterlight intrudes into and
forms a seal with the Rear Roof shell seal
evenly and with no resistance at the front or
the rear.
If the values measured are incorrect or if the
quarterlight encounters any resistance, adjust
as follows.
Adjust the intrusion of the quarterlight into the
seal with the relative travel limit adjuster
screws
(11)
located in the space between the
quarterlight and the bodyshell.
Tightening the adjuster screw decreases the
amount by which the quarterlight intrudes
into the seal, loosening the screw increases
intrusion.
Note that one turn of the front or rear adjuster
screw corresponds to approximately
1 mm
in the height
"Z"
and
0.5 mm
in
"X"
.
Summary of Contents for California
