7
|
ECOTRONIC Plus
© F
er
roli 08164 ECO
TR
ONIC Plus.monen.ind
d
De ltaS ol
M
Main menu
Meas. values
Reports
Solar
GND
S1
S2
S3
S4
S5
S7
S6
S8
S9
S10
S11
S12
----
CS10
Imp1
Imp2
Bus
VBus
RS232
Sensors
R9-A
R9-M
R9-R
DeltaSol M
L N
R8-A
R8-R
R7-A
R7-R
R6-A
R6-R
R5-A
R5-R
R4-A
R3-A
R2-A
R1-A
floating re la y
e
lectr omechanic re la y
semi-conductor r ela y
Schutzleiter -Sammelklemmenblock benutzen
Nullleiter -Sammelklemmenblock benutzen
N
Use the PE Collectiv e T
erminal Block
Use the Neutral Conductor Collecti ve T erminal Block
N
Masse-Sammelklemmenblock ben utzen
Use the Gr ound Collectiv e T
erminal Bloc k
T6,3A
Netz / Mains 220...240
V~
V or Öffnen der Klemmenabdeckung
Gerät spannungslos schalten
Isolate mains befor e re moving clamp-co ve r
6,3 (1) A 220 ... 240 V~
GND
PE
L
N
PE
N
®
®
Netz / Mains
220 ... 240 V~
1.2.5 Mains supply
The power supply to the controller must be carried out via
an external power switch (last step!) and the supply voltage
must be 220 ... 240 V~ (50 ... 60 Hz). Flexible cables must be
attached to the housing with the enclosed strain relief and the
corresponding screws or be run into the controller housing
in a cable conduit or trunking (see advice on page 4).
Mains connection
:
1 = protective conductor (common terminal block)
2 = neutral conductor N (common terminal block)
3 = conductor L
De ltaS ol
M
Main menu
Meas. values
Reports
Solar
GND
S1
S2
S3
S4
S5
S7
S6
S8
S9
S10
S11
S12
----
CS10
Imp1
Imp2
Bus
VBus
RS232
Sensors
R9-A
R9-M
R9-R
DeltaSol M
L N
R8-A
R8-R
R7-A
R7-R
R6-A
R6-R
R5-A
R5-R
R4-A
R3-A
R2-A
R1-A
floating re la y
e
lectr omechanic re la y
semi-conductor r ela y
Schutzleiter -Sammelklemmenblock benutzen
Nullleiter -Sammelklemmenblock benutzen
N
Use the PE Collectiv e T
erminal Block
Use the Neutral Conductor Collecti ve T erminal Block
N
Masse-Sammelklemmenblock ben utzen
Use the Gr ound Collectiv e T
erminal Bloc k
T6,3A
Netz / Mains 220...240
V~
V or Öffnen der Klemmenabdeckung
Gerät spannungslos schalten
Isolate mains befor e re moving clamp-co ve r
6,3 (1) A 220 ... 240 V~
GND
PE
L
N
PE
N
®
®
1.2.4 Bus
The controller is equipped with two bus interfaces for data
communication:
1.) The
VBus
®
for data transfer with and energy supply to
external modules. The connection is carried out at the
two terminals marked “
VBus
®
“ (any polarity). One or
more
VBus
®
modules can be connected via this data
bus:
• WMZ calorimeter
• large displays
• HKM, modular heating circuit expansion
2.) The
RS232-interface
for direct connection to a PC.
Measured values and parameters of the controller can
be read out, adjusted, processed and visualised by means
of the evaluation tool RSC (
S
ervice
C
enter Software).
The software allows easier paramatrisation and function
control of the system.
RS232-connection
RJ45 socket
VBus
terminal
