background image

     

4

If you change parameter 39 to “Yes,” this command requires the User password.

Page 27

To do this

Use this key sequence

Delete last character typed.

[BACKSPACE] or [CTRL]-[H]

Delete line.

[CTRL]-[X]

Pause displays that take more than one screen.

[CTRL]-[S]

Resume scrolling. (Turn Pause off.)

[CTRL]-[Q]

402 Entering Commands from a Terminal or Computer

To monitor or control FERRUPS from a terminal or computer, simply type in one of the commands and press
[ENTER]. (See the table below.) You can type the command in uppercase or lowercase, and you can use the
whole command or the short form, or you can abbreviate the command as long as you include the letters in the
short form. You can also enter more than one command on a line if you put a semicolon between commands.

Command

Short Form

Password

Function

alarmshelp

ah

None

Shows a list of all possible alarm messages, the audio code and letter
for each alarm and whether the alarm is active.

alarmlog

al

None

Displays Alarm Log. See 

Section 306

.

alarmtest

at

None

Allows you to test the alarm function. Alarmtest sounds the User
Test alarm (J). See 

Section 304

.

alarmtest cancel

at c

Turns the User Test alarm off.

chargermode

chm

None

4

Shows the FERRUPS’ battery charger mode. By entering a mode after
the chargermode command, you can change the charger mode:
chargermode off (chm f) or chargermode disable  (chm d) = charger
off; chargermode on (chm o) or chargermode enable (chm e) =
charger on; chargermode auto (chm a) = charger enabled if AC input
voltage and battery voltage are acceptable.

clearalarms

ca

None

Clears all active alarms.

clearhistory

ch

None

Clears the minimum and maximum parameter values shown when you
use the extendedhistory or history commands.

clearpassword

cp

None

Clears the current password.

commands

cm

None

Displays a list of all valid commands.

contdisplay

cd

Depends on

parameter

password

Continuously displays the parameter that you are currently displaying.
You can specify other parameters for the continuous display by
entering the name or number of each parameter after the contdisplay
command.

contstatus

cs

None

Continuously displays the Status information. (See the status
command.)

date

da

None

Displays system time and date. To set the date, enter date
[month]/[day]/[year]
.

Summary of Contents for FSS-0342J













































Reviews: