System manual CECX / Bus link module CECX-B-CO
34.8.1.3 Error codes
The following table lists the meaning of the Error-Codes (according to
DS301)
The error buffer can be read out via object 0x1003:
Error Code
(hex)
Significance
Reaction
0x0000
Error Reset or No Error
0x2320
Short circuit at output
0x3000
Voltage error, input voltage out-
side permitted range or sensor
failure
according to 0x1029/3 change to
XXX_ERROR
The manufacturer-specific Error
Field contains the K-Bus ID and
the status byte of the AM299/X
0x5000
Device Hardware (Error message
triggered through K-Bus module)
Change to PRE_OPERATIONAL
_ERROR
The manufacturer-specific Error
Field contains the K-Bus ID and
the status byte of the AM299/X
0x5001
Device Hardware (K-Bus)
Change to
PRE_OPERATIONAL_ERROR
0x5002
Device Hardware (K-Bus):
Error at Power-Down Line (remains
active after start-up)
Change to
PRE_OPERATIONAL_ERROR
0x5003
Device Hardware (K-Bus):
Error at Power-Down Line
(remains active after start-up)
Change to
PRE_OPERATIONAL_ERROR
0x5004
The K-bus has more modules than
permitted
Change to
PRE_OPERATIONAL_ERROR
0x5005
K-Bus WAIT-Line is blocked by a
device
Change to
PRE_OPERATIONAL_ERROR
0x5007
A K-Bus module was unplugged
from the K-Bus
Change to
PRE_OPERATIONAL_ERROR
0x5008 SERR-Line
active
Change to
PRE_OPERATIONAL_ERROR
0x5009
At least one unknown module is
attached to the K-Bus
Change to PRE_OPERATIONAL
0x500A
Several modules of the same type
detected with the same address
(hex-switch position)
Change to
PRE_OPERATIONAL_ERROR
0x5030
HW-counter overflow before the
previous counter was reset
Change to
PRE_OPERATIONAL_ERROR
0x5031
Sensor failure line A
Change to
PRE_OPERATIONAL_ERROR
0x5032
Sensor failure line B
Change to
PRE_OPERATIONAL_ERROR
0x5033
Sensor failure zero impulse line
Change to
PRE_OPERATIONAL_ERROR
0x5034 Track
error
Change to
PRE_OPERATIONAL_ERROR
0x5035
Zero impulse error A
Change to
PRE_OPERATIONAL_ERROR
0x6000
Device Software (Assertion Failure,
Watchdog)
Module Reset
0x8100 Communication
(Sync-Timeout)
according to 0x1029/1 change to
XXX_ERROR
CECX-II 34-23
Summary of Contents for CECX-X-C1 Series
