background image

9

Commissioning

CAUTION!

Risk of injury due to unexpected movement of components.

Protect the positioning range from unwanted intervention.

Keep foreign objects out of the positioning range.

Perform commissioning at low speed.

NOTICE!

Material damage due to incorrect or incomplete installation.

The following conditions must be fulfilled for commissioning:

The system must be fully assembled.

The electrical installation must be complete and checked.

The pneumatic installation must be complete and checked.

Prior to commissioning, a safety analysis must be carried out and all appropriate measures implemen-
ted. Commissioning is dependent on the customer-specific application.

During commissioning, observe the associated documentation for the installed individual com-
ponents 

è

 1.1 Applicable documents.

Web visualisation of the balancer controller CECC-D-BA enables commissioning via the web browser

è

 1.1 Applicable documents.

Power supply

When switching on the power supply, proceed as follows:
1. Switch on the power supply.
2. Switch on the compressed air supply.

10

Operation

Operation is dependent on the customer-specific application.
Supplementary notes on operation 

è

 Additional documents.

During operation, observe the associated documentation for the individual components installed

è

 1.1 Applicable documents.

Commissioning

14

Festo — YHBP — 2020-09

Summary of Contents for YHBP



















Reviews: