► To do this, place the depth stop on the bit as
shown in figure
[3b]
.
► The bit can be taken out by tilting the depth
stop with the bit, while pulling at the same
time.
► Then place the new bit in the bit holder.
9
Working with the machine
9.1
Switching on/off [1-2]
The tool is not started by pressing the
switch
[1-2]
alone –
not a tool fault
!
Once the screw is driven to the de
sired depth, the tool switches off au
tomatically.
There are numerous ways to switch the tool on:
a)
► Set the tool's rotational direction to clock
wise using the right/left switch
[1-3]
.
► Move the selector switch
[1-4]
to the MAN
position.
► To switch the tool on, actuate the
switch
[1-2]
and at the same time, press on
the screw with the drill bit.
By pressing on the switch
[1-2]
, the speed can
be infinitely adjusted.
b)
► Set the tool's rotational direction to clock
wise using the right/left switch
[1-3]
.
► Move the selector switch
[1-4]
to the AUTO
position.
► To activate the tool, press on the screw with
the drill bit.
It is not necessary to press the switch
[1-2]
.
The top speed is set automatically.
c)
► Set the tool's rotational direction to anti
clockwise using the right/left switch
[1-3]
.
► Switch the tool on using the switch
[1-2]
.
The MAN/AUTO selector switch
[1-4]
is in
either position.
By pressing on the switch
[1-2]
, the speed can
be infinitely adjusted.
The drywall screwdriver rotates anti
clockwise by pressing on the
switch
[1-2]
only, without also having
to press on the bit.
To unscrew screws fully, the depth
stop does therefore not need to be re
moved.
9.2
Depth stop
Turning on the depth stop
[1-5]
sets the screw
ing depth, as shown in figure
[4]
. The setting is
accurate to approx. ± 0.1 mm.
Anticlockwise rota
tion
Screw is countersunk
further out.
Clockwise rotation
Screw is countersunk
further in.
Once the depth setting is made, drive in a test
screw then, if necessary, correct the depth.
Attaching the depth stop
► Place the depth stop
[3-1]
on the transmis
sion housing
[3-5]
.
► Then, apply pressure until the depth stop
audibly clicks into place.
Removing the depth stop
► Take the depth stop out of the transmission
housing by pulling firmly.
9.3
Frame hook and belt clip
The belt clip
[5-1]
can be used to attach the tool
to working clothes temporarily – it can be af
fixed to the left or right-hand side of the tool
using a screw
[5-2]
, making it suitable for
right-handed and left-handed operators – see
figure
[5]
.
The tool also has a hook
[6-1]
, by which the tool
can be hung, as required. It can be affixed to the
left or right-hand side of the housing using the
screw
[6-2]
– see figure
[6]
.
9.4
Magazine attachment
The magazine attachment enables the operator
to work continuously without unnecessary pau
ses.
Fitting the magazine attachment
► Remove the depth stop
[3-1]
on the bit
holder
[3-2]
using the bit, as described in
section
8
.
► Move the selector switch
[1-4]
to the MAN
position.
► Push the long bit
[7-1]
into the tool hold
er
[3-4]
until it clicks into place.
► Then affix the magazine attachment to the
transmission housing. The magazine at
tachment must audibly click into place.
► The magazine attachment can be positioned
at 30° increments.
Removing the magazine attachment
► Take the magazine attachment out of the
transmission housing by pulling firmly.
English
16
