PSC 420 EB
21
GB
up to approx. 2100 rpm: continuous light
from approx. 2100 rpm: stroboscope light
In overhead position (+/- 45°), the lighting is
switched off completely.
If required, you can adjust the lighting:
Plug in the electric power tool.
Press both buttons simultaneously
[1-2]
and
hold for approx. 10 s until a beep sounds.
Release both buttons
[1-2]
.
Press the left button (on the pendulum stroke
side) to select the stroke speed and conse-
quently the desired operating mode:
Press the right button to save the setting.
8.2
Acoustic warning signals
Acoustic warning signals sound and the machine
switches off in the following operating states:
9
Service and maintenance
Customer service and repair
only
through manufacturer or service
workshops: Please find the nearest
address at: www.festool.com/service
Use only original Festool spare parts!
Order No. at: www.festool.com/service
Damaged safety devices and components must be
repaired or replaced in a recognised specialist
workshop, unless otherwise indicated in the oper-
ating manual.
Observe the following instructions:
– Keep the air slits on the machine and the charger
free and clean to ensure adequate cooling.
– Keep the contacts on the machine, charger and
battery pack clean.
– Check the guidance roller regularly for wear.
– Regularly remove dust deposits from the chip
guard.
– Regularly clean the base runner to prevent
scratches and cores on the surface.
Information on battery packs
– Store in a cool, dry place at a temperature be-
tween 5 °C and 25 °C.
– Protect battery packs from moisture, water and
heat.
– Do not leave flat battery packs in a charger dis-
connected from the mains power supply for lon-
ger than one month. Danger of deep discharge!
– If you intend to store li-ion battery packs for lon-
ger periods without use, you should charge them
to 40 % capacity (approx. 15 min charging time).
– To avoid short circuits the battery pack should be
stored in the packaging supplied.
– Significantly shorter operating times after each
charge indicate that the battery pack is worn and
should be replaced with a new one.
10
Accessories
The order numbers of the accessories and tools can
be found in the Festool catalogue or on the Internet
under "www.festool.com".
10.1
Saw blades, other accessories
In order to saw different materials quickly and
cleanly, Festool offers saw blades for all applica-
tions that are specially designed for your Festool
jigsaw.
Mode
Indication during
configuration
Behaviour
during operation
1
Light flashes
With stroboscope
(standard)
2
Light on
Permanent light
without strobo-
scope
3
Light off
Light switched off
Battery flat or machine over-
loaded.
– Change the battery.
– Place the machine under reduced
stress.
Machine is overheating.
– You must allow the machine to
cool before using again.
LiIon battery pack is faulty or has
overheated.
– Once the battery pack has cooled,
perform a functional check using
the charger.
WARNING
Risk of injury, electric shock
Always disconnect the battery pack from the
machine before any maintenance or care work!
All maintenance and repair work which requires
the motor housing to be opened, must only be
carried out by an authorised service workshop.
EKAT
1
2
3
5
4
Summary of Contents for T 15+3 Li
