22
PSC 420 EB
GB
10.2
Sawing with special base runners
The special base runners protect high-quality sur-
faces against scratches and scores.
Press in the base runner at position
[7-1]
.
At the same time, push the base runner for-
wards.
Mount another base runner and push it to the
rear until it engages.
10.3
Sawing with the angle table
The angle table WT-PS 400 is used for cutting pipes
or interior and exterior angles up to 45°.
Dust extraction is not possible when sawing
with the angle table!
Installing the angle table
Remove the saw base
[1-10]
Position the angle table against the saw base
support.
Close the lever
[1-8]
.
Ensure that the angle table is firmly seated in the
guide.
Setting the angle
Turn the adjusting wheel
[8-1]
to select the re-
quired angle.
You can select the angles -45°, 0° and +45° on the
scale
[8-2]
.
For 90° cuts, we recommend setting the angle
table to a small negative angle to guarantee
smooth operation.
10.4
Sawing with the adaptation table
The adaptation table ADT-PS 400 is used for fitting
your jigsaw on the Festool guide rail and the circle
cutter KS-PS 400.
With guide rail and circle cutter:
do not ex-
ceed max. material thickness of 20 mm and
always use cross-set saw blades (FSG).
Installing the adaptation table
Remove the saw table
[1-10]
Mount the adaptation table
[9-1]
on the saw ta-
ble support.
Close the change lever
[1-8]
.
Ensure that the adaptation table is firmly seated in
the guide.
Use the extractor connector
[1-7]
also with the
adaptation table.
Adaptation to the guide rail FS 2
The Festool guide system FS 2 (Fig.
[10]
) makes it
much easier to manufacture straight precision
cuts.
Place the jigsaw with attached adaptation table
[9-1]
on the guide rail.
Adaptation to the circle cutter
The circle cutter can be used to create circular cuts
with a diameter between 120 and 3000 mm. The cir-
cle cutter can be installed from both sides on the
adaptation table.
Place the jigsaw with attached adaptation table
on the adapter
[11-1]
on the circle cutter.
Insert the centring mandrel
[11-2]
in the hole
[11-4]
on the circle cutter aligned with the saw
blade.
Clamp the measuring tape to the circle cutter
using the rotary knob
[11-5]
.
Recommended when using the circle cutter:
Cut in an anticlockwise direction.
Work at a slow rate of advance.
Set the pendulum stroke
[1-11]
to 0 - 1.
Set the stroke rate
[1-5]
to 1 - 5.
Store the centring mandrel in the depot
[11-3]
.
11
Transport
The lithium-ion batteries are subject to the require-
ments of the legislation on hazardous goods. A li-
ion battery pack alone falls below the applicable
limit value and certified as per UN manual ST/SG/
AC.10/11/rev. 3 part III, subsection 38.3. However,
dangerous goods regulations may apply when sev-
eral battery packs are transported For shipping by
third parties (e.g. air transport or freight forward-
ing company) special requirements with regard to
packaging and labelling must be observed.For the
preparation of the package an expert on hazardous
goods must be consulted. Please observe any fur-
ther national regulations.
Only return the battery pack if the housing is un-
damaged. Tape over the exposed contacts and wrap
the battery pack so that it cannot move inside the
packaging.
WARNING
Sawing cutting depths
Risk of injury
Select the saw blade length and cutting depth so
that the saw blade remains plunged in the work-
piece.
Summary of Contents for T 15+3 Li
