14
T 15+3 Li, T 18+3 Li
GB
should either become damaged, in order to avoid
a hazard, have them replaced by an authorised
after-sales service workshop.
– Always pull the mains plug out of the socket
when the charger is not in use.
2.4
Emission levels
Levels determined in accordance with EN 60745 are
typically:
Vibration emission value a
h
(vector sum for three
directions) and uncertainty K measured in accor-
dance with EN 60745:
Vibration emission value a
h
(vector sum for three
directions) and uncertainty K measured in accor-
dance with EN 60745:
The specified emissions values (vibration, noise)
– are used to compare machines.
– They are also used for making preliminary esti-
mates regarding vibration and noise loads during
operation.
– They represent the primary applications of the
power tool.
Increase possible for other applications, with other
insertion tools or if not maintained adequately. Take
note of idling and downtimes of machine!
3
Intended use
Cordless drill suitable for
– drilling in metal, wood, plastic and similar mate-
rials,
– inserting and tightening screws
– use with Festool batteries BPC and BPS of the
same voltage.
Charger TCL 3
suitable for
– charging Festool battery packs: BP, BPS and
BPC (NiMH, NiCd, li-ion are recognised automat-
ically.)
– indoor use only.
The user is liable for improper or non-in-
tended use; this also includes continuous in-
dustrial operation.
4
Technical data
* Speed specifications with fully charged battery pack.
** The maximum speed is reduced in the lower torque stages.
Further technical data on the charger and battery packs can be found on page 6.
Sound pressure level
L
PA
= 65 dB(A)
Sound power level
L
WA
= 76 dB(A)
Uncertainty
K = 3 dB
Wear ear protection.
Drilling in metal
a
h
< 2,5 m/s
2
K = 1,5 m/s
2
Screwing
a
h
< 2,5 m/s
2
K = 1,5 m/s
2
Cordless drill
T 15+3 Li
T 18+3 Li
Motor voltage
14,4 - 15,6 V
18 V
Idle engine speed*
1st gear
0 - 450 min
-1
2nd gear
0 - 1500 min
-1
Max. torque
Soft material (wood)
27 Nm
30 Nm
Hard material (metal)
40 Nm
45 Nm
Adjustable torque**
1st gear
0,5 - 8 Nm
2nd gear
0,5 - 8 Nm
Chuck clamping range
1,5 - 13 mm
Drill diameter max.
Wood
35 mm
45 mm
Metal
16 mm
16 mm
Tool holder in drill spindle
1/4 ’’
1/4 ’’
Weight without battery pack with Centrotec
1,0 kg
1,0 kg
Summary of Contents for T 15+3 Li
