PSC 420 EB
19
GB
7
Settings
7.1
Changing tools
Selecting saw blade
Only use saw blades with a T-shank. The
saw blade should not be longer than that re-
quired for the intended cut. To ensure safe
guidance, during the cut the saw blade should
emerge at the bottom of the workpiece at every
point.
Only use cross-set saw blades when using the
angle and adapter table. We recommend Fes-
tool saw blade S 105/4 FSG.
Inserting saw blade
Always disconnect the battery pack from the
machine before every tool change!
If necessary, lift up the chip guard
[4-1]
.
Slide the saw blade
[4-4]
into the opening
[4-2]
as far as the stop with its teeth in the cutting di-
rection.
Turn the saw blade
[4-4]
clockwise approx. 30°.
Check that the saw blade is secure. A loose
saw blade can fall out and cause an injury.
If the saw blade is very small, it is advis-
able to remove the saw base (see chapter 7.4)
before inserting the saw blade.
Adjust the saw blade guide after every saw blade
change:
The saw blade guide was designed to improve guid-
ance of the saw blade.
Remove the saw base (see chapter 7.4).
Tighten the screw
[4-6]
using the Allen key
[4-
5]
until the jaws are
almost
touching the saw
blade.
Ejecting saw blade
When ejecting the saw blade, hold the electric
power tool such that no persons or animals can
be injured.
Push the saw blade ejection
[4-3]
forwards as
far as the stop.
A tool change is only possible when the tool
holder is located in the upper position!
If the saw blade is stuck and cannot be changed:
Operate the jigsaw at high speed for 3 - 10 seconds.
Actuate the saw blade ejection
[4-3]
again.
7.2
Using the chip guard
The chip guard
[4-1]
prevents chips flying away and
improves the efficiency of the chip extraction sys-
tem.
Using minimal pressure, push the chip guard
[4-1]
downwards.
7.3
Inserting the splinterguard
The splinterguard prevents the edges of the mate-
rial from splintering during the cut, even at the end
where the saw blade exits the material.
Switch off the machine and slide the splinter-
guard
[5-1]
into the guide
[5-2]
and up to the
saw blade,
Switch on the jigsaw,
On a level surface, slide in the splinterguard
(not using your hand!)
while the machine is op-
erating until it is flush with the front edge of the
saw base (speed setting 5). This beds in the
splinterguard.
When it is worn, push the splinterguard approx.
3 mm further to the rear and continue using it.
To guarantee reliable operation of the splinter-
guard, it must seal tightly on both sides of the
saw blade. A new splinterguard should there-
fore be fitted after every saw blade change to
guarantee splinter-free cuts.
7.4
Changing saw table
Open the change lever
[1-8]
.
Removing the saw table downwards.
LED red - lit continuously
Battery temperature is outside
the permitted range.
WARNING
Risk of injury
Always disconnect the battery pack before per-
forming any type of work on the machine!
CAUTION
Hot and sharp tools
Risk of injury
Do not use insert tools that are blunt or defec-
tive.
Wear protective gloves.
NOTE
Damage to the machine or saw blade
Do not tighten the screw [4-6] too firmly! It must
be possible to move the saw blade slightly.
Summary of Contents for T 15+3 Li
