[1-8]
Drilling/impact drilling selector
switch
[1-9]
Gear switch
[1-10] Rotational direction switch and safety
lock/transport lock
[1-11] Handle
[1-12] Thumbwheel for torque/drilling/light
ing duration on and duration off
[1-13] Belt clip
[1-14] Bit store
[1-15] Insulated gripping surfaces (grey
shaded area)
Accessories shown or described are not always
included in the scope of delivery.
The specified illustrations appear at the begin
ning of the Operating Instructions.
6
Battery pack
Before using the battery pack, check that the
battery interface is clean. Any contamination of
the battery interface may impair correct contact
and lead to the contacts being damaged.
A faulty contact may result in the machine over
heating or being damaged.
[2A]
Remove the battery pack.
[2B]
klick
Insert the battery pack – until it
clicks into place.
Further information about the charger and
battery pack with capacity indicator can be
found in the corresponding operating
manual.
7
Commissioning
CAUTION
Risk of injury
► Only assemble when the power tool is
switched off!
7.1
Belt clip [1-13]
The belt clip allows the power tool to be attach
ed to work attire for brief periods. It can be at
tached to the right or left of the power tool us
ing a screw [3].
7.2
Fitting the auxiliary handle [5]
WARNING! Always use the auxiliary handle.
► Check that the auxiliary handle [5-1] is se
curely in place.
7.3
Inserting the stop bar [6]
The drilling depth can be adjusted using the
stop bar [6-1].
7.4
Switching on/off [1-5]
Press = ON, release = OFF
The speed can be continuously adjusted,
relative to the pressure applied to the
on/off switch.
Set the rotational direction switch [1-10] to the
centre position to lock the on/off switch.
The LED light [1-4] lights up when the on/off
switch [1-5] is pressed, see section
8
Settings
CAUTION
Risk of injury
► Only adjust the settings when the power
tool is switched off.
8.1
Changing direction of rotation [1-10]
–
Switch to the left = clockwise rotation
–
Switch to the right = counterclockwise rota
tion
8.2
Changing gear
The gear switch [1-9] can be used to switch the
gear unit when the power tool is switched off.
8.3
Adjusting the torque [1-12]
Screwdriving
Torque corresponding to setting at the thumb
wheel [1-12]:
Position 1 = low torque
Position 13 = high torque
There is a signal when the set torque is
reached and the power tool switches off. The
power tool only starts up again if the on/off
switch [1-5] is released and pressed again.
Drilling
Marking shows the drill symbol
= maxi
mum torque.
8.4
Adjust lighting [1-12]
Configure lighting at the thumbwheel [1-12].
Marking shows position 1 to 13 or drill sym
bol
. The LED light [1-4] automatically
switches on and off with the power tool. The
LED light has an afterglow for a short time after
the tool has been switched off.
English
17
Summary of Contents for TPC 18/4
Page 2: ...2B 2A BP C 18 1 klick 2 1 1 3 1 2 1 4 1 5 1 6 1 8 1 9 1 10 1 12 1 14 1 15 1 7 1 11 1 1 1 13 ...
Page 3: ...5 1 3 4 2 2 2 4 Nm klick 3 5 1 ...
Page 4: ...6 7 6 1 3 8 KC 13 WH CE CENTROTEC 2 1 1 2 1 3 3 4 klick 2 1 klick klick klick 3 4 klick ...
Page 5: ...9 10 12 AN UNI 11 EX UNI DC UNI FF 3 12 1 klick 1 2 2 1 3 1 2 3 B A 4 ...
