background image

 

Contact Information

 

 

FETCO

®

 

Food Equipment Technologies Company 

600 Rose Road 

Lake Zurich 

 IL 

 60047-0429 

 USA 

Internet: 

www.fetco.com 

©2013-2020 

Food Equipment Technologies Company 

 

Go to fetco.com for the latest version of all information 

 

Phone:

 (800) 338-2699 (US & Canada) 

(847) 719-3000 

Fax:

 (847) 719-3001 

  

Email:

 sales@fetco.com 

              techsupport@fetco.com 

PATENTS: WWW.fetco.com/patents   

P11919

    

 REVISED March 2020 

 

 

 

User’s Guide 

 

 

Hot Water Dispenser HWD_2102  With Portion Control

 

Domestic and Export Version 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

                              Table of Contents 

 

Operator And User Sections 

 

Operating Instructions ................................................ 3

 

Operating Principles .................................................. 4

 

Adjusting Temperature and Dispense Portion ........... 5

 

Error Messages ......................................................... 7

 

Cleaning & Maintenance ............................................ 8 

 

 

 

Professional Service Sections

 

 

Equipment Setup ....................................................... 9

 

Parts Diagrams ........................................................ 11

 

Wiring Diagram ........................................................ 14

 

 

Summary of Contents for HWD-2102















Reviews: