background image

Manual for motor FM 170 B2 - FS ( Date of publication 06/2016)

 

 

FIALA PROP s.r.o,  Vysoká 56,  75641 LEŠNÁ ,  Czech Republic , e-mail: valachmotors@fialaprop.cz 
www.fialaprop.com

 

 

Page 3 

 

3.   Fuel 

 Use unleaded gasoline with a minimum octane 95 mixed 

with synthetic oil designed for two-stroke 

engines. 

For running we recommend 1:25, after running 1:30. Run-in should take about 2 hours of operation. 

We recommend Valvoline oil - SynPower 2T - Full Synthetic, Mobil 1 - Racing 2T - Full Synthetic or 
Repsol - Moto2T Racing. If you are not sure about the suitability of oil, which is going to use, contact  
authorized service center or the manufacturer directly.  

4.  Propeller 

With the engine FM 170 B2 - FS we recommend the following propellers: two-blade 32/12, 34/12. 
Three-blade 30/12, 30/14. 

For best results use Fiala propellers.

 

With these propellers motor should be measured on the ground to achieve optimum speed, ie 
approx. 4500 - 5000 rev / min. When installing and using the propeller observe strictly all safety 
recommendations propeller manufacturer. Propeller is mounted on motor by  a central bolt M10x 1 
and six screws around the perimeter of the flange. 

5.   First start of the motor 

Properly attach the motor to the model or the test stand using all four screws. Connect the ignition 
source (4.8 - 9V, min. capacity of 1500 mAh). Connect the fuel tank. 

- Make sure that the ignition is switched off 

- Close the choke 

- 5-6 x crank the motor in order to suck fuel 

- Adjust slightly increased idle speed cca 10% 

- Turn on the ignition 

- Start the motor 

- If after about 5 attempts, the engine does not start, repeat the procedure again 

 

Note : ignition is equipped with a security protection function, because if it is turned on and the 
motor is more than a minute at rest, the ignition is switched off. In this case, it is only the ignition off 
and on again. For more information see the instructions on electronic ignition. 

 

 

 

Summary of Contents for FM 170 B2-FS









Reviews: