FIAP premiumactive FEEDER
Technische Änderungen vorbehalten. Für Druckfehler übernehmen wir keine Haftung. WEEE-Reg. Nr.: DE78152045
9
FIAP GmbH, Jakob Oswald Str. 16, 92289 Ursensollen
Tel: 09628 9213 0; Fax: 09628 9213 30;
www.fiap.com
Connecting the battery
Connect the battery cables as follows: red + / white on –
•
If the battery is connected, the two LED flash on the display. Flashing them, remove the cable
from the battery and connect it again after about one minute, then the Clock enough time to
reset.
•
The timer is working with the 6 volt battery or battery loses, but after disconnecting the
battery's memory. After connecting everything must be re-entered.
•
If the memory retain any data even after disconnecting the battery should be a button cell
(CR2032) are used in the timer.
•
Does the timer does not work properly, or does the display after the display, the button cell
should be replaced.
Setting the time
Set the time by pressing the hours (hour) and minutes (minute) button.
AM stands for the morning
and PM for the afternoon.
Setting the feeding time
Press the menu button on the left below appears in the display "a spin". Spin stands for feeding time.
Set the first Feeding time by pressing the hour and minute button.
Setting the amount of feed
By pressing the "Menu" key the display shows "Spin Time 1. With this function you can set the duration
of the discharge volume. Possible are 10-60 seconds with the key HR with time goes into the red, and
the MIN into Plus. By a pressing the "Menu" key the display shows "Spin 2". Proceed to continue as
described under "Setting the feeding time and adjusting the amount of food" until you set all the
desired feed time. However, it is not necessary to activate all six feeding times.
Deleting individual feed times
This press the button as long hours to "OFF" is displayed. Conversely, you can activate when "OFF"
the display will appear again this time by typing a time with the HR and MIN button.
Setting the power of the engine
If you have entered the food times and continue to press the "Menu" appears in the display "engine
speed". The performance of the engine can be over the control to 50 % (low) 75 % (medium) and 100
% (set high). With the key HR to handle the power down, again with the MIN button to the top.
System Test
The last function appears when you press the Menu button, the display shows "TEST". Now press the
key HR appear in the display "Stand Clear". The timer now counts down to 0 10 seconds, then start
the test run! You have put so 10 seconds to be out of reach. The test run will always take as many
seconds as in "Spin a Time" was set.
CAUTION: Wear the test run and as you approach the feeder - safety glasses! When the engine
starts the feed at high speed is thrown from the machine, therefore look for when test run
especially on the eyes and keep well clear!
FIAP premiumactive FEEDER
Technische Änderungen vorbehalten. Für Druckfehler übernehmen wir keine Haftung. WEEE-Reg. Nr.: DE78152045
10
FIAP GmbH, Jakob Oswald Str. 16, 92289 Ursensollen
Tel: 09628 9213 0; Fax: 09628 9213 30;
www.fiap.com
Clearing the memory
If you press PROG-HR-MIN simultaneously, the display shows "Reset all?". The timer counts 5
seconds back in 00:00, the entire memory erased. When you release the keys before, the data
obtained.
Cleaning
To ensure a good continuity with the feedings, FIAP premiumactive FEEDER during the season now
and again to be cleaned. Remove with a small brush the dust and food residues from the distribution
table.
Store / hibernate
Clean for the winter and dry the food container and keep the equipment until the following spring in a
dry and frost-free place.
No.
1 2 3 4 Solar
Paneel
Plug
Art.
Akku(+)
Akku (-)
Motor (+)
Motor (-)
Sun (+)
Sun (-)
Color:
Red Black Orange
Blue White
Brown
