background image

1

assigned to the device status - sending the BASIC SET (default) or ALARM control frame to the 

associated devices having detected fire. (max. nodes in group: 5)

2

assigned to a TMP button and the malfunction alarm. Alarm frame will be sent to the associated 

devices once tampering or malfunction are detected. (max. nodes in group: 5)

3

reports the device status and allows for assigning single device only (the main controller by default - 

the device reports its status to the main controller). (max. nodes in group: 1)

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can 

adapt the function better to user needs or unlock further enhanced features.

IMPORTANT: Controllers may only allow to configure signed values. In order to set values in the range 128 

… 255 the value sent in the application shall be the desired value minus 256. For example: to set a 

parameter to 200? it may be needed to set a value of 200 minus 256 = minus 56. In case of two byte value 

the same logic applies: Values greater than 32768 may needed to be given as negative values too.

Smoke alarm cancellation delay (Parameter Number 1, Parameter Size 2) time period, during which the 

Smoke Sensor will keep indicating the smoke alarm after smoke will have disappeared

Value

Description

0 — 

17280

0 - no delay, immediate cancellation 65535 - alarm cancellation inactive - Smoke Sensor will 

keep indicating smoke alarm after the smoke will have disappeared. The smoke alarm can be 

only ceased manually, by entering 2nd menu level (Default 0)

LED indicator and acoustic alarm turned ON / OFF at any alarm type (Parameter Number 2, Parameter 

Size 1) activates/deactivates the LED indicator and acoustic alarm for any alarm type. Doesn’t affect the Z-

Wave alarm.

Value

Description

0

acoustic and visual alarms inactive

1

acoustic alarm inactive, visual alarm active

2

acoustic alarm active, visual alarm inactive

3

acoustic and visual alarms active (Default)

(c) 2012 Z-Wave Europe GmbH, Goldbachstr. 13, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 9 

Summary of Contents for FIB_FGSS-101















Reviews: