background image

14

BATTERY

To add an association

 (using the home Center controller):

1.  Go to the device options by clicking the icon: 
2.  Select the „Advanced” tab.
3.  Click the “Setting Association” button.
4.  Specify to which group and what devices are to be associated.
5.  Save the changes.
6.  Click 

 

and 

 

simultaneously to wake up the device.

Paired buttons associations

After pairing buttons, horizontal pairs of buttons (  and  ,   and  , 

 and  ) work as one button and send associations to left buttons 

groups only. 
Left buttons ( ,  ,  ) turn on associated devices and right buttons  

( ,  ,  ) turn them off. 
In multilevel association groups (3, 7, 11) left buttons increase level 

while holding and right buttons decrease it.

To pair buttons:

 

1.  Change settings of parameters:

• 

 and   – set parameter 6 to value 1

• 

 and 

 

– set parameter 7 to value 1

• 

 and 

 

– set parameter 8 to value 1

2.  Save the changes.
3.  Click 

 

and 

 

simultaneously to wake up the device.

The KeyFob in 2nd to 13th group allows to control 5 de-

vices (regular or multichannel) per an association group. 

 

“LifeLine” group is reserved solely for the controller and hence only 1 

node can  be assigned.
It is not recommended to associate more than 10 devices in general, 

as the response time to control commands depends on the number of 

associated devices. In extreme cases, system response may be delayed.

Summary of Contents for KEYFOB FGKF-601






















Reviews: