background image

EN

8

FDAH 200

2

General safety instructions 

FDK 2001-E

12

EN

General safety instructions

Position the Jack

Position the jack to only lift on the areas of the vehicle as specified by the vehicle 

manufacturer.

Always Use Jack Stands

After lifting the vehicle always support the load with appropriately rated vehicle 

Jacks stands before working on the vehicle.

Do Not Overload Jack

Do not overload this jack beyond its rated capacity. Overloading this jack 

beyond its rated capacity can cause damage to or failure of the jack.

Always Use on Hard Level Surfaces

This jack is designed only for use on hard level surfaces capable of sustaining the 

load. Use on unstable or other possible loss of load.

Chock and Block (Stabilize)

Apply parking brake in vehicle before operating jack.

A chock is a wedge for steadying an object and holding it motionless, or for 

preventing the movement of a wheel Chock the wheel opposite the end being 

lifted.

When you block a load, you secure and support a load that is being lifted. The 

block(s) or stabilizer(s) should have a weight capacity that is greater than the 

weight of the load which is being lifted.

Do not move or dolly the vehicle while on the jack.

Lift only on areas of the vehicle as specified by the vehicle manufacturer.

No alterations shall be made to this product.

Only attachments and/or adapters supplied by the manufacturer shall be used.

Do not get under or allow anyone under the vehicle until it has been supported by 

jack stands.

Center load on saddle prior to lifting.

Use wheel chocks or other blocking device on opposing wheels before using jack.

Never use on a lawn mower or lawn tractor.

Do not use this jack for any use other than the manufacturer specified usage.

Do not rock the vehicle while working on or around equipment.

Failure to heed these markings may result in personal injury and/or property damage.

GENERAL SAFETY INSTRUCTIONS

Study, understand, and follow all instructions before operating this device.
Do not exceed rated capacity.
Use only on hard, level surfaces, with less than 3 degrees of slope.
Lifting device only. Immediately after lifting, support the vehicle with 

appropriate means.
Do not move or dolly the vehicle while on the jack.

WARNING!

SAFETY MARKINGS

Summary of Contents for FDAH 2002





















Reviews: