EN
9
FZN 4001-A / FZN 4002-AT
Putting into operation
Function of the swivel head
(see pic. 6)
Firmly hold the handle. Move the locking button upwards and then turn the tool's head to the desired
position. Release the locking button and check that the tool's head is properly secured in the new
position.
Note:
The tool's head can be secured in fi ve positions (-90°, 0°, 90°, 180°).
Turned at an angle of 90° for vertical cutting of lawns - see pic. 7, 10.
Turned at an angle of 180° for cutting at heights - see pic. 8.
Setting the height for cutting and trimming lawns - see pic. 9.
Appropriate height for cutting lawns is 40 and 25mm.
Appropriate height for trimming lawns is 80, 65 and 40mm.
Charging the machine
(see pic. 11)
If you wish to charge the battery, connect the adapter to a power socket (230 V ~ 50 Hz) and insert the
charger connector into the opening on the handle of the machine. The red charging indicator light will
turn on. The battery may be charged for approximately 4 hours. Make sure that you have read all the
safety instructions before using the charger. This product must not be repaired by the user. There are
no repairable parts inside the charger. The charger must be repaired by an authorised service centre
or organised by the vendor so as to prevent damaging the internal components. Read all instructions
contained in this user's manual in the section describing the charger before charging your tool's
battery.
1. Charging procedure
These chargers do not require any setup and are designed so that their use is as easy as possible.
Connect the charger to the tool. (Insert it into the charger opening on the handle).
Connect the charger power cord to a power socket. A LED charging indicator will turn light up on the
tool. Now the LED charging indicator will be red. This means that the battery is charging.
The LED diode will turn green after approximately 4 hours. This means that the battery is fully charged.
Note:
The start safety lock and the start button on the tool do not function during the charging
process.
2. Important notes for charging.
You will achieve the longest operating lifetime and performance if the battery is charged at
temperatures between 18 - 24 °C. Do not charge the battery at temperatures lower than +4.5 °C or
higher than +40 °C. This instruction is very important and prevents major damage to the battery.
While charging the charger and the battery may be warm to touch. This is a normal event and does
not indicate any problem.
Whenever possible use the charger at standard room temperature. To prevent the charger from overheating
do not cover the battery and do not charge in direct sunlight or in the vicinity of heat sources.
If the battery is not being properly charged:
1
connect a lamp or another device to the power socket to check the current in the socket.
2
check whether the socket is controlled via a light switch, which turns off the socket when the light
is turned off.
Summary of Contents for FZN 4001-A
