Fieldmann FZN 4002 B Manual Download

Page: 20 / 27

PETROL-POWERED HEDGE TRIMMER

USER'S MANUAL

Maintenance

2. Certain maintenance products and certain solvents may damage plastic components. These products

include those containing benzene, trichloroethylene, chloride and ammonia.

3. Make sure that all ventilation openings on the power tool remain clear and unclogged. To ensure cleanliness

inside the power tool it is usually sufﬁ cient to clean using a soft brush and then blowing it out with
compressed air.

4. Wear appropriate eye protection when performing cleaning.

GEARBOX

The gearbox needs to be lubricated every 30 operating hours. For this task, we recommend that you contact an
authorised service centre.

REPAIRS

Repairs on this power tool may only be performed at an authorised service centre.

Problem

Inspection

Status

Cause

Solution

The engine is stopping, it is

difﬁ cult to start or cannot be

started at all

Fuel in the

carburettor

Fuel is not

reaching the

carburettor

Clogged fuel

ﬁ lter

Clean out or replace

Clogged fuel

supply line

Clean out or replace

Carburettor

Request a repair at

an authorised service

centre

Fuel is returning

Fuel is not

reaching the

cylinder

Carburettor

Request a repair at

an authorised service

centre

There is fuel in the

exhaust pipe

The fuel mix is

too rich

Open the choke

valve. Clean out or

replace the air ﬁ lter.

Adjust the carburettor.

Request a repair at

an authorised service

centre.

Sparks on the

spark plug

electrodes

No spark

The engine

switch is in the

off position

Set the engine switch

to the ON position

Electrical

system

problem

Request a repair at

an authorised service

centre

Locked switch

Summary of Contents for FZN 4002 B



























Search results

Summary of Contents for FZN 4002 B

Reviews:

Related manuals for FZN 4002 B

Brands by name

Popular brands

Fieldmann FZN 4002 B, Manual

Search results

Summary of Contents for FZN 4002 B

Reviews:

Related manuals for FZN 4002 B

Brands by name

Popular brands