background image

17

OPERATION MANUAL

GASOLINE BRUSH CUTTER

EN

What to do “if…”

Unsufficiently functional 
engine

Possible cause

Remedy

1. Check the air filter.

Dirty air filter

Clean or replace the air filter 
element.

2. Check fuel.

Fuel contains water.

Drain the fuel tank and the 
carburettor. Fill new fuel into 
the tank.

Improper fuel mixture ratio.

3. Check the primer setup and 
gas control.

The primer not fully open.

Adjust the setup.

Wrongly adjusted gas cable.

4. Bring the engine to the 
authorized  service or to the 
dealer.

Clogged fuel filter, carburettor 
fault, ignition fault, clogged 
valves etc.

Replace or repair defective 
parts.

Engine starts-up, 
conks out immediately

Possible cause

Remedy

1. Check fuel.

Fuel has run out.

Fill up fuel

Fuel contains water.

Drain the fuel tank and the 
carburettor. Fill new fuel into 
the tank.

Improper fuel mixture ratio.

2. Take the spark plug 
out and check.

Defective or dirty spark plug.

Replace the spark plug.

Wrong gap between electrodes.

3. Check the air filter.

Dirty air filter. Clogged air filter

Clean or replace the air filter 
element.

4. Bring the engine to the 
authorized  service or to 
the dealer.

Clogged bleeder valve.

Replace or repair defective 
parts.

Clogged fuel filter, carburettor fault, 
ignition fault, clogged valves etc.

Summary of Contents for FZS 4003-B


















Reviews: