background image

EN

PETROL BRUSH CUTTER

USER'S MANUAL

5

General safety instructions

1. GENERAL SAFETY INSTRUCTIONS

Important safety notice

  Carefully unpack the product and take care not to throw away any part of the packaging before you fi nd all 

the parts of the product.

  Store the product in a dry place out of reach of children.
  Read all warnings and instructions. Not following warnings or instructions may lead to injury by electrical 

shock, a fi re and/or serious injuries.

Packaging

The product is packed in a package that prevents damage during transport. This package is a resource and so 
can be handed over for recycling.

User’s Manual

Before you start working with the machine, read the following safety and usage instructions. Acquaint yourself 
with the operating elements and the correct use of the machine. Keep the user’s manual in a safe place where 
it can be easily retrieved for future use. Save the original packaging, including the internal packing material, 
warranty card and proof of purchase receipt at least for the duration of the warranty. If you need to ship this 
machine, pack it in the original cardboard box to ensure maximum protection during shipping or transport 
(e.g. when moving or when you need to send this product for repair).

 

Note:

 If you hand over the machine to somebody else, do so together with the user’s manual.

 

Following the instructions in the included user’s manual is a prerequisite for the proper use of the machine. 
The user’s manual also contains operating, maintenance and repair instructions.

The manufacturer takes no responsibility for accidents or damages resulting from not 
following the instructions in this manual.

Summary of Contents for FZS 5025-B































Reviews: