FieldServer Gardner Denver FS-8700-60 Instruction Manual Download

Page: 4 / 13

FS-8700-60 Gardner Denver Manual

Page 2 of 11

FieldServer Technologies

1991 Tarob Court Milpitas, California 95035 USA

Web

:www.fieldserver.com

Tel

: (408) 262-2299

Fax

: (408) 262-9042

Toll_Free

: 888-509-1970

email

: support@fieldserver.com

Driver Scope of Supply

1.01

Supplied by FieldServer Technologies for this driver

FieldServer Technologies
PART #

Description

FS-8915-10

UTP cable (7 foot) for RS-232 use

FS-8917-03

RJ45 to DB9M connector adapter

FS-8700-60 Driver

Manual

1.02

Provided by the Supplier of 3

Party Equipment

2.1.1. Required

Party Hardware

Part #

Description

- ES/RS2000

controller

2.1.2. Required

Party Software

None.

2.1.3. Required

Party Configuration

The ES/RS2000 Controller must be set up in the correct mode to support either
RS-232 or RS-485 communications to an external monitoring system. Please
refer to manufacturer’s setup instructions.

2.1.4. Optional

Items

PART #

Vendor/Manufacturer

Description

485LDRC

B&B Electronics

RS-232/RS-485 converter

Summary of Contents for Gardner Denver FS-8700-60














Search results

Summary of Contents for Gardner Denver FS-8700-60

Reviews:

Related manuals for Gardner Denver FS-8700-60

Brands by name

Popular brands

FieldServer Gardner Denver FS-8700-60, Instruction Manual

Search results

Summary of Contents for Gardner Denver FS-8700-60

Reviews:

Related manuals for Gardner Denver FS-8700-60

Brands by name

Popular brands