Federal Communications Commission (FCC)
Agency Listings, Approvals, and Requirements
FCP-300/FCP-300ECS Manual —
P/N LS10145-002FK-E:A 3/12/2021
13
Section 2: Agency Listings, Approvals, and Requirements
2.1 Federal Communications Commission (FCC)
The following information must be provided to the Telephone Company before the FCP-300 can be connected to the phone
lines:
This equipment complies with Part 68 of the FCC Rules and the Requirements adopted by ACTA. On the inside cover of this
equipment is a label that contains, among other information, a product identifier. If requested, this information must be pro-
vided to the Telephone Company.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable
FCC Part 68 Rules and Requirements adopted by the ACTA. A compliant telephone cord (not provided) and modular jack
must be used with this product. It is designed to be used with a modular jack that is also compliant.
The REN (ringer equivalence number) provided on this document is used to determine the number of devices that may be con-
nected to the Public Switched Telephone Network. This number must not exceed 5.0. Since this product has an REN of 1.0A,
the number of devices is limited. The REN number is embedded in the FCC registration number as 10A.
If the FCP-300 or FCP-300ECS causes harm to the Telephone Network, the Telephone Company will notify you in advance
that the Service may be required to be temporarily discontinued. However, if advance notice is not practical, the Telephone
Company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC
if you believe it is necessary.
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the opera-
tion of the equipment. If this occurs, the Telephone Company will provide advance notice in order for you to make necessary
modifications to maintain uninterrupted service.
If a trouble event is experienced with the FCP-300 or FCP-300ECS, for repair or warranty information, please contact Fike
Customer Service at 800-979-3453 (Fike) or www.fike.com
.
If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect the FCP-
300 until the problem is resolved.
This product cannot be adjusted or repaired in the field. It must be returned to the factory for service.
This equipment is not designed for use with party line service. The connection to the party line service is subject to state tariffs.
You may contact the State Public Utility Commission, Public Service Commission or Corporation Commission for informa-
tion.
Since the FCP-300 or FCP-300ECS are commercial fire alarm panels, they must be connected upstream of all other equipment
using the phone lines. If you have questions about the installation, contact your Telephone Company or a qualified installer.
A
Manufacturer:
Fike Corporation
B
Model Number:
FCP-300 and FCP-300ECS
C
FCC registration number:
US: HS9AL10A2100
Ringer equivalence:
1.0A
D
Type of jack:
RJ31X
E
Facility Interface Codes:
Loop Start: 02LS2
F
Service Order Code:
9.0F
!
WARNING:
This device has been verified to comply with FCC Rules Part 15. Operation is subject to the
following conditions: (1) This device may not cause radio interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
!
CAUTION 1:
To ensure proper operation, this equipment must be installed according to the enclosed installation
instructions. To verify that the equipment is operating properly and can successfully report an alarm, this equipment
must be tested immediately after installation, and periodically thereafter, according to the enclosed test
instructions.
!
CAUTION 2:
In order for “Alarm Dialing Equipment” to be able to seize the phone line to report an alarm or other
event when other customer equipment (telephone, answering System, computer modem, etc.) connected to the
same line are in use, the “Alarm Dialing Equipment” must be connected to a properly installed RJ31X jack.
The RJ31X jack must be connected in series (sequentially) with, and ahead of, all other equipment attached to the
same phone line. The Series installation of an RJ31X jack is depicted in the figure below. If you have any questions
concerning these instructions, you should consult your Telephone Company or a qualified installer about installing
the necessary jack and alarm dialing equipment for you.
Summary of Contents for FCP-300
Page 169: ...Cut Along the Dotted Line ...
Page 171: ...Cut Along the Dotted Line ...
Page 173: ...Cut Along the Dotted Line ...
Page 175: ...Cut Along the Dotted Line ...
