114
FCP-300/FCP-300ECS Manual —
P/N LS10145-002FK-E:A 3/12/2021
System Operation
Basic Operation
Disable / Enable NACs by Template
1.
Press 1 for Disable NACs by Template, or press 2 to Enable NACs by Template.
2.
Use the up or down arrow key to move the cursor through the list of templates. Press ENTER to select the current
template.
Disable / Enable NACs by Group
1.
Press 3 to Disable NACs by Group, or press 4 to Enable NACs by Group.
2.
Use the up or down arrow key to move the cursor through the list of groups. Press ENTER to select the group highlighted.
Disable / Enable Zone Points
1.
Press 5 to Disable Zone Points, or press 6 to Enable Zone Points.
2.
Use the up or down arrow key to move the cursor through the list of zones. Press ENTER to select the zone highlighted.
Disable / Enable Point
1.
Press 7 to access the Disable /Enable Point.
2.
Choose the Module.
3.
Use the up or down arrow key to choose the Point and press ENTER.
4.
Press the right arrow key to disable or enable the Point.
Inhibit Output Group
Inhibiting an output group prevents the group from being used by System Mapping. While inhibited, no event in the System
can activate the output group.
1.
Press 8 to access the Inhibit Output Group.
2.
Use the up or down arrow key to select the group to be inhibited.
3.
Press the right arrow to inhibit the group.
4.
Press the right arrow again to enable the group.
10.4.3 View Event History
Use the View Event History feature to display the events on the LCD. From the Main Menu, press 3 to select Event History.
The Events will begin displaying with the most recent events first.
The panel can store up to 1000 events. When it reaches its 1000-event capacity, it will delete the oldest events to make room
for the new events as they occur. In Networked setups, each panel stores up to 1000 of its own events. When you view the
Event History in the panel, the most recent 500 events from every panel in the site will be displayed. When you use the HFSS
Programming Tool, all 1000 events from every panel in the network will be uploaded.
On the multi-site displays, pressing ENTER or the right arrow key brings you directly into the View Event History and allows
you to view the Event History from every panel in each of the sites that the multi-site display is assigned to.
To clear the Event History, do the following.
1.
From the Installer Menu, select 1 for System Tests.
2.
From the Test Menu, select 6 Clear History Buffer.
3.
In Network Systems, this clears the History Buffer of all panels in the site.
10.4.4 Conduct a Fire Drill
1.
From the Main Menu, press 1 for System Tests.
2.
Press 1 for the Fire Drill. You will be prompted to press ENTER.
3.
The drill will begin immediately after you press ENTER.
4.
Press any key to end the drill. (If you do not press any key to manually end the fire drill, it will automatically time-out
after ten minutes).
5.
If a fire drill switch has been installed, activating the switch will begin the drill; deactivating the switch will end the drill.
10.4.5 Conduct an Indicator Test
The Indicator Test checks the annunciator LEDs, PZT, and LCD display.
1.
From the Main Menu, press 1 for the System Tests.
2.
Press 2 for the Indicator Test. The System turns on each LED several times, beeping the PZT as it does so. At the same
time, it scrolls each available character across the LCD. A problem is indicated if any of the following occurs:
• An LED does not turn on.
• You do not hear a beep.
• All four lines of the LCD are not full.
This test takes approximately 15 seconds to complete. You can press any key to manually end while the Test is still in progress.
When the Test ends, you will be returned to the <Test Menu>.
Summary of Contents for FCP-300
Page 169: ...Cut Along the Dotted Line ...
Page 171: ...Cut Along the Dotted Line ...
Page 173: ...Cut Along the Dotted Line ...
Page 175: ...Cut Along the Dotted Line ...
