Filtrete 3M-50 Install Manual Download

Page: 17 / 18

Wire Reference Chart

Possible Wires

What They Control

R or V or VR

and

Single power for HEAT and COOL

RH or 4

Power for HEAT (RH not connected to RC jumper clip removed)

Power for COOL (RH not connected to RC jumper clip removed)

Heat control

2nd stage HEAT or heat pump auxiliary heat

3rd stage HEAT or 2nd stage of 2 stage auxiliary heat

COOL control or 1st stage compression for heat pump

2nd stage COOL control or 2nd stage compression for a heat pump

G or F

FAN control

C or X

24VAC power (to power thermostat)

NOTE: TRANE uses B for this connection

External Humidifier

External De-Humidifier

external fresh air baffle

Heat pump changeover (cool to heat, powered in heat)

Heat pump changeover (heat to cool, powered in cool)

B and O

IMPORTANT: If there are both B and O wires (Trane pump

products) DO NOT CONNECT B to B terminal, connect B to C

terminal. If not a Trane product tape off B.

n/a Emergency heat (do not connect, tape off)

n/a System monitor (do not connect, tape off)

n/a Outdoor sensor (do not connect, tape off)

Summary of Contents for 3M-50



















Search results

Summary of Contents for 3M-50

Reviews:

Related manuals for 3M-50

Brands by name

Popular brands

Filtrete 3M-50, Install Manual

Search results

Summary of Contents for 3M-50

Reviews:

Related manuals for 3M-50

Brands by name

Popular brands