INSERTING WATER SYSTEM FILTER
Before using the machine for the first time the water system filter needs to be reset, for shipping reasons the filter cartridge and the cap have
been removed. To insert the filter cartridge in the water system filter body proceed as follows:
1. Take the machine to the maintenance area.
2. Carry out the steps necessary to secure the machine (see paragraph “MACHINE SAFETY” on page 11).
ATTENTION:
It is recommended to wear the appropriate PPE (Personal Protective Equipment), suitable for the work to be carried out.
3.
Move to the front left of the machine and tighten the tap outflow, turn the lever (7) located in the tap body clockwise (
Fig.9
).
4.
Insert the filter cartridge (8) in the housing on the cap (9) (
Fig.10
).
N.B.:
The o-ring gasket (10) in the filter cartridge must be inserted into its seat in the cap (
Fig.10
).
5.
Screw the cap (9) onto the body of the filter (11) (
Fig.11
).
FILLING THE SOLUTION TANK
Before filling the solution tank, carry out the following steps:
1.
Take the machine to the usual place for filling the solution tank.
2. Carry out the steps necessary to secure the machine (see paragraph “MACHINE SAFETY” on page 11).
3.
Move to the front of the machine and check that the water system filter cap (9) is tightened, otherwise tighten it (
Fig.11
).
The solution tank can be filled with water in two different ways:
•
Removing the cap/measuring device (12) and filling the solution tank by means of a rubber hose or a bucket (
Fig.12
).
•
Inserting the filling tube in the hole (13) located in the cap/measuring device (12) (
Fig.13
), the hole is able to support the filling tube by itself.
4. Fill with clean water, at a temperature no higher than 50°C (122°F) and no lower than 10°C (50°F). The amount inside the tank can be seen
by means of the level tube (14) on the left-hand side of the machine (
Fig.14
).
DETERGENT SOLUTION
After filling the solution tank with clean water, add the liquid detergent to the tank in the concentration and manner indicated on the detergent
manufacturer's label.
To prevent the formation of an excessive amount of foam that could damage the vacuum motor, use the minimum percentage of detergent
required.
ATTENTION:
It is recommended to wear the appropriate PPE (Personal Protective Equipment), suitable for the work to be carried out.
ATTENTION:
always use detergents whose manufacturer's label indicates their suitability for scrubbing machines. Do not use acid or
alkaline products or solvents without this indication.
ATTENTION:
always use low-foam detergent. To avoid the production of foam, put a minimum quantity of antifoam liquid in the recovery
tank before starting to clean. Do not use pure acids.
ASSEMBLING THE BRUSH HEAD BRUSH (SCRUBBING VERSION)
To fit the brush on the brush head body, proceed as follows:
1. Release the control column from the vertical position, press the stop lever (3) (
Fig.3
) and turn the control column towards yourself (
Fig.15
).
2.
Turn the column towards yourself to find the optimal position, this position must provide a sensation of comfort when using the machine.
Once the ideal position has been found, release the stop lever (2) to lock the column.
3.
Place the brush on the floor and place the brush head body over it (
Fig.16
).
4. Activate the machine by pressing the button (2) located on the control panel (
Fig.2
).
5. Press the operator presence lever (15) (
Fig.17
), the gearmotor will activate and the brush will be connected to the brush retainer plate.
ATTENTION:
during this operation, check there are no people or objects near the machine.
ASSEMBLING THE ABRASIVE PAD (ORBITAL VERSION)
To fit the brush on the brush head body, proceed as follows:
1. Release the control column from the vertical position, press the stop lever (3) (
Fig.3
) and turn the control column towards yourself (
Fig.15
).
2.
Turn the column towards yourself to find the optimal position, this position must provide a sensation of comfort when using the machine.
Once the ideal position has been found, release the stop lever (2) to lock the column.
3.
Position the abrasive pad on the floor and place the brush head body on top of it.
14
