SCRUBBING WITH DRYING
Selecting the program “SCRUBBING WITH DRYING”, the control display screen will appear as shown
in the figure.
NB
: with this working program, the pressing of the dead man's lever brings both the brush
head and the squeegee to the work position (in contact with the floor). When the dead man's
lever is pressed, all the motors are powered. The brush head solenoid valve and the water
system pump are powered up (only if the detergent solution level is not at zero).
NB
: on the DS selector, the symbol of the scrubbing with drying program (D) is green.
NB
: the grey symbols show working programs that are not active. the green symbols show
working programs that are active.
NB
: when the dead man's lever is released, the brush head motor and the vacuum motor stop
with the relative delays. After the “Reset Delay” time, the brush head and squeegee body are
taken to their idle position (raised off the floor). When the dead man's lever is pressed, work will
resume with the same working program and parameters used prior to the stop.
NB
:
if you reverse while this program is active, the brush head body will remain in contact with
the floor and the motor will continue working, but the solenoid valve will not deliver detergent
solution to the brushes. The squeegee support is taken to its idle position (raised off the floor)
and the vacuum motor is switched off with the relative delay.
The icons that may be visible are:
1. FFM symbol, if visible it shows that the “FIMAP FLEET MANAGEMENT” system operating.
2. FSS symbol, if visible it shows that the “FIMAP SOLUTION SAVER” system is operating.
3. General alarm symbol.
ATTENTION
: if visible, stop the machine. To continue working, see “ALARM SCREEN”.
4.
Solution tank empty float symbol.
ATTENTION
: if visible, it indicates that the detergent solution in the tank has a reached a level
beyond which the solenoid valve cannot deliver solution onto the brushes, so the tank needs to
be filled up before continuing the work (see “
”).
5. ECO-MODE button.
NB
: if the Eco-Mode button (5) is pressed in transfer mode, the “scrubbing with drying”
program is activated in economic mode.
6. Menu button.
7. Zone button.
NB
: if the Zone button (8) is pressed in transfer mode, the window for selecting the zone opens
(see “
”). Once you have selected an area, “scrubbing with drying”
is activated for the area selected.
8. Text indicator.
NB
: the text indicator (8) shows which zone program has been selected, or whether the
machine is in transport mode if the word “DRIVE” is visible.
ATTENTION: never switch off the machine with the squeegee and/
or brush head in contact with the floor
DS SELECTOR (DRIVE SELECT)
The DS selector can be used to select one of the following working programs:
A. Transfer: movement of the machine without working.
B. Scrubbing only: using only the brushes in the brush head.
C. Drying: using the squeegee only.
D. Scrubbing with Drying: using both the brushes and the squeegee.
Pressing one of the symbols in the selector, you pass from the working screen (
Fig. 1
) to the program
selection screen (
Fig. 2
). On this screen it is possible to:
1.
Confirm the selected program.
NB
: to confirm the program, press the selected icon again.
NB
: once the selection has been confirmed, you will return to the working screen (
Fig. 1
).
2. Cancel the selection and return to the working screen
NB
: to cancel the selection, press the “back” button (1) (
Fig. 2
) to return to the working screen
without changing the current program.
NB
: to cancel the selection, wait 5 seconds without selecting anything and you will return to the
working screen without changing the current program.
3. Select a mode other than the one highlighted.
ECO MODE
In the centre of the DS selector there is the ECO-MODE key (1). Press it to activate the “ECO-MODE”
program, which provides the best possible performance in terms of consumption and cleaning. To
activate the ECO-MODE program, proceed as follows:
1. Sit on the driver’s seat.
2. Insert the key (1) in the main switch on the control panel. Set the main switch to “I” by making a
quarter turn of the key to the right (
Fig. 1)
).
3. Select the ECO-MODE working program with the button (2) at the centre of the DS selector
(
Fig. 2
).
NB
: A grey ECO-MODE key means that economic mode is not active. A green ECO-MODE
key means that economic mode is active. In addition, when ECO-MODE is active, on the text
indicator row (3) on the display, the words “ECO mode” will appear (
Fig. 2
).
NB
:
pressing the button (2) on the DS selector (
Fig. 2
) will activate the SCRUBBING WITH
DRYING program. If you wish to use another working program, select it using the DS selector
(read the section “
”).
4. When you push the dead man's lever (4), the machine will begin to move (
Fig. 3
).
N.B.:
if the button (2) is pressed when working in ECO-MODE, the machine will shift to
MANUAL MODE, leaving the program in use at the time active (
Fig. 4
).
N.B.:
if the “ZONE” button (4) is pressed when working in ECO-MODE, the machine will shift to
PROGRAM ZONE mode (
Fig. 2
); as soon as button (4) is pressed, the screen enabling you to
select the working zone will appear on the display (
Fig. 5
).
19
MANUAL
0000.00
100%
Back
0000.00
100%
A
B
D
C
1
1
2
ECO mode
0000.00
100%
2
5
3
2
MANUAL
0000.00
100%
Warehouse
Canteen
Office
Reception
Exit
SELEZIONE ZONE
0000.00
100%
4
5
3
4
1
1
OFFICE
0000.00
100%
1
3
2
4
6
8
7
5
Summary of Contents for MAXIMA 2017 PLUS
