RECOMMENDED MAINTENANCE OPERATIONS
DRAINING THE RECOVERY TANK
Proceed as follows to empty the recovery tank:
1. Take the machine to the maintenance area.
2. Make sure the machine is in a safe condition (see “
CAUTION:
users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
3. Release the recovery tank drainage tube (on the back of the machine) from the retainers (
Fig. 1
).
4. Bend the end of the drainage tube in order to create a choke and prevent the content from coming
out (
Fig. 2
), then position the tube on the discharge surface, unscrew the cap, and gradually
release the tube.
NB:
the place designated for this operation must comply with current environmental protection
regulations.
5. Repeat the operations in reverse order to reassemble all the parts.
CLEANING THE DEBRIS HOPPER (50BTS VERSION)
To clean the debris hopper, proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “
CAUTION
: users are advised to always wear protective gloves, to avoid the risk of serious injury
to hands.
3. Use the moulded handle (1) to extract the debris hopper (
Fig. 1
) and empty it.
NOTE
: the place designated for this operation must comply with current environmental
protection regulations.
4.
Clean the inside with a jet of water, and use a brush to remove any residual impurities if necessary.
5. Proceed in the opposite order to reassemble all the parts.
To clean the debris hopper (with the optional spray gun kit), proceed as follows:
1. Take the machine to the maintenance area.
2. Using the DS selector on the control display (
Fig. 1
), select the “transfer” program” (1).
3. Use the moulded handle (2) to extract the debris hopper (
Fig. 2
) and empty it.
CAUTION
: users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
4. Release the tank cleaning accessory (3) (at the back of the machine) from the retainers (
Fig. 3
).
5.
Activate the optional tank cleaning kit ON/OFF pump by pressing the button (4) on the back of
the machine (
Fig. 4
).
CAUTION
: when using the optional tank cleaning kit, you are advised to always wear goggles
to avoid any risk of serious injury to your eyes.
N.B.
: before activating the optional tank cleaning kit, check the level indicator (5) to see how
much solution there is in the recovery tank (
Fig. 5
).
6.
Activate the solution jet by pressing the lever in the tank cleaning accessory. Make sure the jet is
pointing into the tank before pressing the lever.
NB
: to adjust the solution jet from the
tank cleaning accessory, turn the knob (6) on the
accessory itself
(
Fig. 6
).
NB
: to adjust the intensity of the solution jet from the
tank cleaning accessory, turn the knob (7)
on the accessory itself
(
Fig. 7
).
NB
: to stop the solution jet,
use the lever (8) on the tank cleaning accessory (
Fig. 8
).
NOTE
: the place designated for this operation must comply with current environmental
protection regulations.
7.
Clean the inside with a jet of water, and use a brush to remove any residual impurities if necessary.
8. Repeat the operations in reverse order to reassemble all the parts.
CLEANING THE SQUEEGEE BODY
The careful cleaning of the whole vacuum unit ensures better drying and cleaning of the floor as well as
a longer vacuum motor life. To clean the squeegee body, proceed as follows:
1. Take the machine to the maintenance area.
2. Make sure the machine has been secured (see the section titled “
”).
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3. Remove the vacuum tube (1) from the vacuum nozzle on the squeegee body (
Fig. 1
).
4. Completely unscrew the knobs (2) in the squeegee body pre-assembly (
Fig. 2
).
5. Remove the squeegee body from the slits in the squeegee connector (
Fig. 3
).
23
2
1
4
5
6
4
5
6
7
8
7
8
2
1
3
1
2
1
1
2
3
2
3
Back
0000.00
100%
1
1
TYPE OF MAINTENANCE
AT THE END OF THE
WORK
DAIL
Y
WEEKL
Y
BEFORE A
LONG
PERIOD OF NON-USE
TRANSPORT
EMPTYING THE RECOVERY TANK
X
X
X
CLEANING THE DEBRIS HOPPER (50BTS VERSION)
X
X
X
CLEANING THE SQUEEGEE BODY
X
X
X
CLEANING THE BRUSH HEAD BRUSH (50BT VERSION)
X
X
CLEANING THE BRUSH HEAD BRUSHES (60BT VERSION)
X
X
CLEANING THE BRUSH HEAD BRUSHES (50BT VERSION)
X
X
CLEANING THE RECOVERY TANK FILTERS
X
X
X
CLEANING THE RECOVERY TANK
X
X
X
EMPTYING THE SOLUTION TANK
X
X
X
X
CLEANING THE WATER SYSTEM FILTER
X
X
CLEANING THE VACUUM TUBE
X
X
CLEANING THE SOLUTION TANK
X
X
CLEANING THE VACUUM WAND KIT
X
X
X
Summary of Contents for MAXIMA 2017 PLUS
