background image

WARNING:

•  Always protect the machine against sunlight, rain, and other atmospheric agents, both while 

it is stationary and while it is functioning. Store the machine in a dry, sheltered place: this 

machine is only designed for use under dry conditions, and must not be used or stored 

outdoors in humid conditions.

•  Do not park the machine near combustible materials, powders, gases or liquids.

• 

Stop the machine on a flat surface.

• 

Make sure the electric brake is engaged, then switch off the machine via the main switch 

(removing the key from the block) and disconnect the battery connector from the electrical 

system connector.

•  If the machine is left unattended, it must be protected from any accidental movements

ATTENTION:

•  The machine must only be stored under temperature conditions ranging from 0 °C to +40 °C. 

The humidity level must be between 30% and 95%.

DEACTIVATION OF THE MACHINE

DANGER:

•  To avoid short-circuits when working in the vicinity of electrical components: avoid the use of 

non-insulated tools; do not place or allow metallic objects to fall upon the electrically powered 

components; remove rings, watches and/or clothing with metallic parts that might come into 

contact with the electrically powered components.

• 

Do not work underneath the raised machine without adequate fixed safety supports.

WARNING:

• 

Read  all  the  relevant  instructions  carefully  before  performing  any  maintenance/repair 

operations.

•  If the machine does not work properly, check this is not caused by failure to carry out routine 

maintenance. Otherwise, ask for the intervention of the authorised technical assistance centre.

•  Restore all electrical connections after any maintenance interventions.

CAUTION:

• 

When doing maintenance work, switch off the machine using the main switch. Remove the 

key from the block and disconnect the battery connector from the electrical system connector.

• 

Avoid contact with moving parts. Do not wear loose clothing or jewellery, and tie long hair 

back.

•  Block the wheels before lifting the machine.

•  Lift the machine with equipment that can sustain the weight to be lifted.

ATTENTION:

•  Never tamper with the machine protection devices for any reason. Always follow the supplied 

routine maintenance instructions scrupulously.

MAINTENANCE

8

Summary of Contents for MAXIMA BASE BT 2017





























Reviews: