SCRUBBING WITHOUT DRYING
To perform a scrubbing only program, proceed as follows:
1. Carry out all the checks listed in the chapter “
2. Connect the plug (1) of the power cable (2) to the mains supply socket (3) (
Fig.1
).
CAUTION:
We recommend handling the power cable with dry hands to avoid serious injury.
3. Go to the driving position, behind the machine.
4. Switch on the machine by setting the main switch to “I”, press the button (4)
(Fig.2)
.
NB
:
if the LED in the button switch (4) is on it means that the switch is set to “I” (
Fig.2
). if the
LED in the button switch (4) is off it means that the switch is set to “0”.
5. Set the main key switch to “I”, turn the key (5) by a quarter turn to the left (
Fig.3
).
3
5
2
4
1
2
3
1
6. Lower the brush head body and detach the "BRUSH HEAD CONTROL" pedal (6) at the back of
the machine (
Fig.4
).
7. When the dead man's lever (7) is pressed, the machine will begin to move. The lever is located
underneath the control handlebars (
Fig.5
).
NB
:
the brush head body will only begin to descend to its working position when the dead
man's lever has been pressed.
NB
:
the gearmotor will only begin functioning, and the solenoid valve will only begin dispensing
detergent solution, when the brush head body is in its working position.
5
7
4
6
DRYING
To perform a drying program, proceed as follows:
1. Carry out all the checks listed in the chapter “
2. Connect the plug (1) of the power cable (2) to the mains supply socket (3) (
Fig.1
).
CAUTION:
We recommend handling the power cable with dry hands to avoid serious injury.
3. Go to the driving position, behind the machine.
4. Switch on the machine by setting the main switch to “I”, press the button (4)
(Fig.2)
.
NB
:
if the LED in the button switch (4) is on it means that the switch is set to “I” (
Fig.2
). if the
LED in the button switch (4) is off it means that the switch is set to “0”.
5. Set the main key switch to “I”, turn the key (5) by a quarter turn to the left (
Fig.3
).
3
5
2
4
1
2
3
1
6. Lower the squeegee body and turn the squeegee control lever (6) in the direction of the arrow
(
Fig.4
). The lever is located on the back of the machine.
7. When the dead man's lever (7) is pressed, the machine will begin to move. The lever is located
underneath the control handlebars (
Fig.5
).
NB
:
the vacuum motor will only begin to work when the squeegee body is in contact with the
floor.
4
6
5
7
The drying without scrubbing operation should only be
carried out if the machine was previously used to
carry out a scrubbing without drying operation.
ADJUSTMENT OF THE DETERGENT SOLUTION FLOW
To adjust the flow of detergent solution during work, proceed as follows:
1. Make sure the detergent solution tap is fully open, rotating the knob (1) in the direction of
the arrow (
Fig.1
). As the knob is rotated, the flow of detergent in the machine water circuit is
increased.
2. By pushing the dead man's lever (2) the brush motor will start operating and the solenoid valve
will distribute detergent solution to the brush (
Fig.2
).
3.
During the first few meters check that the amount of solution is sufficient to wet the floor, but not
excessive to exit the splash guard.
4. If the amount of chemical that comes out is not suitable, it can be controlled via the knob (1) on
the rear left-hand side of the machine (
Fig.1
).
2
2
1
1
EXTRA BRUSH HEAD PRESSURE
This machine can increase the pressure exerted on the brush during the work cycle. To do this:
1. Check that the brush head body is in contact with the ground; if not, detach the "BRUSH HEAD
CONTROL" pedal (2) at the rear of the machine from the plate retainer (
Fig.1
).
2. Raise the brush head pedal and engage it in the “EXTRA PRESSURE” position (
Fig.2
).
1
2
1
RECOVERY TANK OVERFLOW
The machine is fitted with a mechanical device (float) under the recovery tank lid. When the recovery
tank is full, this device shuts off the air to the vacuum motor in order to protect it; the sound of the
vacuum motor will then be deeper.
If this is the case, proceed as follows:
1. Raise the brush head body and fully depress the "BRUSH HEAD CONTROL" pedal (1) at the
rear of the machine (
Fig.1
).
NB
:
to lock the brush head in the raised position, depress the pedal (1) fully and then move it
towards the right-hand side of the machine (
Fig.1
).
2.
Raise the squeegee body off the floor by means of the lever (2) on the back of the machine (
Fig.2
).
3.
Bring the machine to the designated place for draining off the dirty water, and empty the recovery
1
2
1
2
16
