MACHINE PREPARATION
HANDLING THE PACKAGED MACHINE
The machine is contained in specific packaging, and since the packaging
elements (plastic bags, staples, etc.) are a potential source of danger,
they should not be left within the reach of children, disabled persons, etc.
The machine's overall weight including packaging is 000Kg.
The overall dimensions of the package are: A=765mm B=1460mm
C=1270mm.
ATTENTION
: it is recommended that all the packaging
components be kept for any future machine transportation.
ATTENTION
: move the packaged product with handling
equipment that complies with legal requirements regarding size and mass of the packaging.
HOW TO UNPACK THE MACHINE
The machine is shipped in specific packaging. To remove it, proceed as follows:
1.
Place the lower part of the outer packaging in contact with the floor.
NOTE
: use the pictograms printed on the box as a reference.
2. Remove the outer package.
CAUTION
: these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3.
The machine is fixed to the pallet by means of chocks (1) that block the wheels and brush head
(
Fig.1
), remove these chocks.
4. Raise the brush head body and fully depress the "BRUSH HEAD CONTROL" pedal (2) at the
rear of the machine (
Fig.2
).
NB
:
to lock the brush head in the raised position, depress the pedal (2) fully and then move it
towards the right-hand side of the machine (
Fig.2
).
5. Raise the squeegee body and turn the squeegee control lever (3) in the direction of the arrow
(
Fig.3
). The lever is located on the back of the machine.
1
2
3
1
2
3
6. Use a ramp to bring the machine down from the pallet.
CAUTION
: do not fit the brush and the rear squeegee body before unloading the machine, and
avoid any violent jolts to the brush head and squeegee support.
NB
: the ramp gradient must not be such as to cause damage to the machine as it comes
down.
HOW TO MOVE THE MACHINE
To transport the machine safely, proceed as follows:
DANGER
: before starting any task, make sure the current regulations concerning the safe
transport of dangerous substances are scrupulously observed.
1. Make sure that the solution tank and the recovery tank are empty. If not, empty them (see the
sections “
2. Check that the main key switch on the control panel is set to “0”. If necessary turn the key (1) to
the left (
Fig.1
).
3. Check that the main button switch on the control panel is set to “0”. If necessary press the button
(2) (
Fig.2
).
NB
:
if the LED in the button switch (2) is on it means that the switch is set to “I” (
Fig.2
). if the
LED in the button switch (2) is off it means that the switch is set to “0”.
4. Raise the brush head body and fully depress the "BRUSH HEAD CONTROL" pedal (3) at the
rear of the machine (
Fig.2
).
NB
:
to lock the brush head in the raised position, press the pedal (2) all the way down and
then move it towards the right-hand side of the machine (
Fig.3
).
3
3
1
2
1
2
5. Raise the squeegee body and turn the squeegee control lever (4) in the direction of the arrow
(
Fig.4
). The lever is located on the back of the machine.
6. Use a ramp to move the machine up onto the transport vehicle.
CAUTION
: during this operation, check there are no people or objects near the machine.
N.B.
: the ramp gradient must not be such as to cause damage to the machine as it goes up.
WARNING
: secure the device according to the directives in force in the country of use, so that it
cannot slide or tip over.
4
4
MACHINE SAFETY MEASURES
To ensure that work is carried out in the best safety conditions, proceed as follows:
1.
Switch off the machine by positioning the main switch (1) to “0”
(Fig.1)
.
NB
:
if the LED in the button switch (1) is on it means that the switch is set to “I” (
Fig.1
). if the
LED in the button switch (1) is off it means that the switch is set to “0”.
2.
S witch off the machine setting the main key switch to “0", turn the key (2) to the left (
Fig.2
).
Remove the key from the instrument panel.
3. Disconnect the plug (3) of the power cable (4) from the mains supply socket (5) (
Fig.3
).
2
3
1
2
3
4
5
1
4. Wind up the power cable and put it in the tear-resistant hook (6) in the rear of the machine (
Fig.4
).
CAUTION:
We recommend handling the power cable with dry hands to avoid serious injury.
CAUTION:
To prevent damaging the power cable, disconnect the plug from the mains socket
by directly pulling the plug and not the cable.
5. Make sure the recovery tank is empty. If it isn't, empty it using the tube (7) on the rear left-hand
side of the machine (
Fig.5
").
ATTENTION
: the tanks should be emptied in the place used for draining dirty water.
ATTENTION
: the place designated for this operation must comply with current environmental
protection regulations.
6. Raise the brush head body and push all the way down the "BRUSH HEAD CONTROL" pedal (8)
at the rear of the machine (
Fig.6
).
NB
:
to lock the brush head in the raised position, depress the pedal (8) fully and then move it
towards the right-hand side of the machine (
Fig.6
).
4
6
5
6
8
7
7. Raise the squeegee body and turn the squeegee control lever (9) in the direction of the arrow
(
Fig.7
), the lever is located on the back of the machine.
7
9
13
