Fimco 15-2N-ATV-GS Owner'S Manual Download

Page: 2 / 10

Page 2

Contents of your sprayer’s carton (15-2N-ATV-GS):

Contents of Parts Bag
#5281752

Owner’s

Manual

Step 1

Tank Pre-Assembly

Tank Lid

& Lanyard

Contents of Bracket Kit

#5281761

2-Nozzle Rigid Boom (#5277774)

Assembly Procedure (15-2N-ATV-GS)

Right Hand (RH) and Left Hand (LH) sides of the sprayer are deter-

mined as if you are standing behind the sprayer, looking at it (facing

forward)

After removing the tank from the box, start the assembly procedure by

turning the tank upside on a stable, flat surface.

A 1/2” socket wrench is required for this step.

(**) Mount the tank brackets to the underside of the tank as shown in

Step 1. Use (4) hex bolts to secure it to the tank. The tank will rest on

the surface of the brackets. Make sure the brackets are parallel with

each other before tightening down the bolts. Do not over-tighten.

Entry Level Spray Wand

& 15’ Hose

Summary of Contents for 15-2N-ATV-GS











Search results

Summary of Contents for 15-2N-ATV-GS

Reviews:

Related manuals for 15-2N-ATV-GS

Brands by name

Popular brands

Fimco 15-2N-ATV-GS, Owner'S Manual

Search results

Summary of Contents for 15-2N-ATV-GS

Reviews:

Related manuals for 15-2N-ATV-GS

Brands by name

Popular brands