background image

*** IMPORTANT REMINDER ***

A

"ON/OFF" Valve

Inlet from Tank

Detail A

This unit comes with an On/Off valve, located near

You must make sure the valve is in the

the inlet of the tank, towards the underside. (See Detail A)

"open" position before using your unit.

15 Gal. Corrosion-Resistant Polyethylene Tank

12 Volt Diaphragm Pump, 2.1 g.p.m. - 60 p.s.i.

Low Profile Trailer & Tank

4.10/3.50 x 4 Pneumatic Tires

Pressure Gauge

Adjustable Pressure

2-Nozzle Boom Assembly, 80" Coverage

Technical Specifications

Assembly

Model: LG-1500 (5301140)

Owner's Manual

(15 Gallon Lawn & Garden Trailer Sprayer)

Your sprayer has been partially assembled at the factory. Follow 

the instructions below to complete the assembly of this unit. 

(Refer to the exploded view drawing later in this manual)

1. Bolt the hitch brackets, both formed and flat, to the trailer 

frame.

2. Slide the axle through the frame holes, centering it as best as 

possible.

3. Slide a wheel spacer and a wheel (valve stem out) onto each 

end of the axle, then use a cotter pin to secure the wheels in 

place.

4. Bolt the boom brackets to the back of the frame.

5. Bolt the boom assembly to the boom brackets with the tips of 

the boom facing rearward. The tips need to be approximately 

18" above the spraying surface. Secure in place with (2) bolts 

and nuts provided.

6. Thread the pressure gauge into the end of the manifold 

assembly. Use a good grade of thread sealant, to insure no 

leaks.

7. Remove the drain plug and handgun clips from the parts bag 

and attach them to the tank, as shown.

8. Attach the 'loose' boom feeder hose to the center hose barb 

on the manifold assembly and to the nylon feeder "tee" on the 

boom. Secure in place with 1/2" hose clamps.

9. Connect the electrical hook-up to the end of your pump and 

clip the clips to a fully charged battery. The red wire must be 

connected to the positive (+), and the black wire should be 

connected to the negative (-).

Form No. 1309    [5004803    (03/10)]     Printed in the U.S.A.

General Information

Thank you for purchasing this product. The purpose of this 

manual is to assist you in operating and maintaining your 

lawn & garden trailer sprayer. Please read it carefully, as it 

furnishes information which will help you achieve years of 

trouble-free operation.

Warranty/Parts/Service

Products are warranted for one year from date of purchase 

against manufacturer or workmanship defects.

Commercial users have a 90 day warranty.

Your authorized dealer is the best source of replacement parts 

and service. To obtain prompt, efficient service, always 

remember to give the following information...

 - Correct Part Description and/or part number.

 - Model number/Serial number of your sprayer.

Part descriptions and part numbers can be obtained from the 

illustrated parts list section(s) of this manual.

Whenever you need parts or repair service, contact your 

distributor/dealer first. For warranty work, always take your 

original sales slip, or other evidence of purchase date, to your 

distributor/dealer.

1000 FIMCO Lane, P.O. Box 1700, North Sioux City, SD 57049

Toll Free Phone: 800-831-0027 : Toll Free Fax: 800-494-0440

www.fimcoindustries.com

Summary of Contents for LG-1500

Page 1: ...handgun clips from the parts bag and attach them to the tank as shown 8 Attach the loose boom feeder hose to the center hose barb on the manifold assembly and to the nylon feeder tee on the boom Secure in place with 1 2 hose clamps 9 Connect the electrical hook up to the end of your pump and clip the clips to a fully charged battery The red wire must be connected to the positive and the black wire...

Page 2: ... you did in the testing procedure Conditions of weather and terrain must be considered when setting the sprayer Do not spray on windy days Protective clothing must be worn in some cases Be sure to read the chemical label s correctly WARNING Some chemicals will damage the pump valves if allowed to soak untreated for a length of time ALWAYS thoroughly flush the pump with water after use DO NOT allow...

Page 3: ...e Kit w O Ring Upper Housing Assembly Pressure Switch Assembly Pkg 2 Clips Port Fitting Diaphragm Cam Bearing Kit Rocker Switch Mounting Feet Pkg of 4 Pump runs but does not prime and test Pump will NOT run Part Number 5157205 5168820 5168837 5168839 5157202 20408 000 5168838 5095202 5157207 3 1 4 5 1 5 2 3 2 3 3 Item 1 2 3 No 1 Plunger Kit 1 1 1 1 1 Description 1 1 1 Qty List Price 3 99 19 95 39 ...

Page 4: ...7007 1 Gauge 0 100 p s i 6 25 25 5169242 1 15 Gallon New Style Tank 50 00 26 5274373 1 Drain Plug Cap Tether and Washer Assembly 2 95 27 5274443 1 Lead Wire Assembly w Switch 96 9 99 28 1 5053096 2 Handgun Clip for Blow Molded Tanks 95 28 2 5117293 2 10 24 x 3 8 Phillips Round Head Machine Screw 25 Item No Part Number Qty Description List Price 29 5275553 1 Manifold Assembly 18 00 29 1 5010430 1 P...

Reviews: