background image

10 Troubleshooting 

FAULT 

SOLUTION 

The vacuum turbine does not work, the electric 
motor does not start.  

Check the electrical connections 

Charge the batteries. 

Replace the fuses. 

Inform the support service. 

Insufficient vacuum power. 

Check the gasket on the vacuum head. 

Empty the bin. 

Check and clean the vacuum head filter. 

Inform the support service. 

Noisy operation. 

Lubricate the moving parts.  

Remove or replace the fan and check its fixing. 

Tighten the fan screws. 

Inform the support service. 

Inform the support service. 

11 Technical Specifications 

General Machine Specifications 

Length x Width x Height 

mm 

2000 x 940 x 1780 

Unladen weight 

Kg 

300 

Total permitted weight 

Kg 

350 

Maximum forward speed 

Km/h 

4.5 

Maximum reverse speed  

Km/h 

2.7 

Maximum negotiable slope 

30 

Waste container volume 

240 

Protection rating 

-- 

IPX3 

Power supply 

Gel batteries 

-- 

4x6V = 24V / 240Ah 

 

Tyres 

 

Front dimensions  

mm 

2 x Ø260x85 

Front wheel pressure 

bar 

Solid rubber 

Rear dimensions 

-- 

8” –

 3.50 

Rear wheel pressure 

bar 

Solid rubber 

 

Vacuum System 

 

Standard version filter surface 

m

0.23 

Fine dust version filter surface  

m

2

 

1.2 

Maximum depression 

hPa 

22.5 

Maximum flow rate 

l/s 

470 

 

Environmental Conditions   

Temperature 

°C 

0..40 

Humidity, non-condensing 

0..90 

Vacuum tube vibrations 

m/s

2

 

0.2 

Noise emission at 3 metres 

dB(A) 

69 

 

Summary of Contents for ASPIRIK













Reviews: