background image

 

15 

 

 

 

Heater makes popping noise. 

 

Spiders  and  insects  can  nest  in  burner  or  orifices.  This  dangerous  condition  can  damage  heater  and 
render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help 
clear away smaller particles. 

 

Carbon deposits may create a fire hazard. Clean dome and burner screen with warm soapy water if any 
carbon deposits develop. 

 
Note

: In a salt-air environment (such as near an ocean), corrosion occurs more quickly than normal. Frequently 

check for corroded areas and repair them promptly. 

 
TIP (FOR STAINLESS STEEL MODELS): 

Use high-quality automobile wax to help maintain the appearance of your heater. Apply to exterior 
surfaces from the post down. DO NOT apply to emitter screen or domes. 

 
Storage

Between uses: 

 

Turn Control Knob OFF. 

 

Disconnect LP source. 

 

Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, 
hail, snow, dust and debris). 

 

If desired, cover heater to protect exterior surfaces and to help prevent build-up in air passages. Never 
leave LP cylinder exposed to direct sunlight or excessive heat. 

               

Note

: Wait until heater is cool before covering

 

 
Service

Only a qualified service person should repair gas passages and associated components. 
 

Caution

: Always allow heater to cool before attempting service. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

                                                                         

CARE AND MAINTENANCE 

Summary of Contents for 60951



















Reviews: