background image

 

16 

 

 

Step 15: Secure the bottom of the LP Tank/Cylinder to the Base of the Heater 
 
Hardware Used:    None 
 

Place the LP Tank/Cylinder onto the base of the heater and secure the Base to the Tank by evenly tightening the 
3) M8x25 Bolts (I) which were originally preassembled to the 3 LPG Cylinder Brackets (H) which were thereafter 
assembled to the inside floor of the base during Step #2.    Once the bolts are secured against the base rim of the 
Tank, lower the Tank Housing. 

 
Caution:

 It is important to secure the cylinder tank to the heater base to ensure that the tank is not dislodged 

if accidentally tipped over during severe weather or while being moved. 
 

 
 
 
 
 

A minimum supply pressure of .5 psi is required for the purpose of input adjustment of propane gas. Storage of 
an  appliance  indoors  is  permissible  only  if  the  cylinder  is  disconnected  and  removed  from  the  appliance.  A 
cylinder must be stored outdoors in a well-ventilated area out of the reach of children. A disconnected cylinder 
must have dust caps tightly installed and must not be stored in a building, garage, or any other enclosed area. 
The  minimum  permissible  gas  supply  pressure  of  11  W.C.  is  required  for  purpose  of  hose  adjustment.  The 
minimum hourly of 17,500 BTU is required input rating for a heater for automatic operation rating less than full 
input rating. 
 
The pressure regulator and hose assembly supplied with the appliance must be used. 
 
The installation must conform with local codes, or in the absence of local codes, with national fuel gas code, ANSI 
Z223.1/NFPA54, natural gas and propane Installation Code, CSA B149.1, or propane storage and handling code, 
B149.2 
A dented rusted or damaged propane cylinder may be hazardous and should be checked by your local cylinder 
supplier. Never use a propane cylinder with a damaged valve connection. 
The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders 
of  the  U.S.  Department  of  Transportation  (DOT)  or  the  standard  for  cylinders,  spheres  and  tubes  for 
transportation of dangerous goods and commission, CAN/CSA-B339. 
 
The cylinder must have a listed overfilling prevention device. 
 
The cylinder must have a connection device compatible with the connection for the appliance. 
 
The cylinder used must include a collar to protect the cylinder valve. 
 
Never connect an unregulated propane cylinder to the heater. 

 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 

 

Do not store a spare LP-gas cylinder under or near this appliance. 

 

Never fill the cylinder beyond 80 percent full. 

 

Place the dust cap on the cylinder valve outlet whenever the cylinder 

is not in use. Only install the type of dust cap on the cylinder valve 

that  is  provided  with  the  cylinder  valve.  Other  types  of  caps  or 
plugs may result in leakage of propane. 

 

 
 

OPERATING INSTRUCTIONS

 

ASSEMBLY 

Summary of Contents for PH01-S XL Series
























Reviews: