Firelands X BOLT 250 Assembly Manual Download

Page: 1 / 16

Assembly Manual

Product specifications are subject to change without notice.

Due to ongoing development, the actual product may vary from

images shown.

This product is not a toy! (14+) Recommended for ages 14 and

up. Adult supervision required for ages under 18 years old.

Contains small parts, keep out of reach of children 3 years of

age and younger.

Distributed in the

UK by:

J Perkins Distribution Ltd,

Lenham,

Kent, UK

ME17 2DL.

www.jperkins.com

Distributed in Australia by:

Model Engines (Aust.) Pty. Ltd.,

Unit 1, 158-168 Browns Road,

Noble Park,

Victoria,

3174,

Australia.

www.modelengines.com.au

Ph (03) 8793 5555

warranties@modelengines.com.au

Distributed in the US by:

Firelands Customer Service/Product

Support

1133 Libra Drive, Lincoln, NE 68512

www.firelandsgroup.com

1-800-205-6773

customerservice@firelandsgroup.com

MADE IN CHINA

This product contains chemicals known to the State of California

to cause cancer, birth defects and other reproductive harm.

Electronics

Carbon Fiber Manufactured

and Machined in USA

X Bolt FPV Racer Kit AZSZ2903

Packaged and Assembled

in USA

Summary of Contents for X BOLT 250

















Search results

Summary of Contents for X BOLT 250

Reviews:

Related manuals for X BOLT 250

Brands by name

Popular brands

Firelands X BOLT 250, Assembly Manual

Search results

Summary of Contents for X BOLT 250

Reviews:

Related manuals for X BOLT 250

Brands by name

Popular brands