background image

Page | 19  

12

 

RFI Environments 

The 

control panel’s circuit arrangement provides a number of layers of electronic protection 

designed  to  minimise  the  effects  of  electromagnetic  emissions  and  prevent  accidental 
discharges of the suppression system. 
Shielded, fire rated cable (FP-09500) is required to be used throughout every installation to 
protect  the  fire  system  from  electromagnetic  emissions.    Cables  should  be  installed  with 
appropriate  clearances  from  any  cables  or  equipment  that  may  produce  high  levels  of  RF 
interference.  

13

 

Safety Data Sheet (SDS) - FirePro 

This is an EXTRACT ONLY from the full SDS.  To view the full SDS go to 

www.chemwatch.com.au

 

 
PRODUCT NAME 

CELANOVA FIREPRO 

 
 
PRODUCT USE 

Fire extinguishing agent.

 

HAZARDOUS SUBSTANCE. DANGEROUS GOODS. 

According to NOHSC Criteria, and ADG Code. 

 

POISONS SCHEDULE - 

None 

RISK 

SAFETY 

 

Contact with combustible material may cause fire. 

 

Harmful if swallowed  

 

Irritating to eyes and skin.  

 

May cause SENSITISATION by skin contact.  

 

Harmful  to  aquatic  organisms  may  cause  long-  adverse 
effects in the aquatic environment. 

 

Cumulative effects may result following exposure  

 

May produce discomfort of the respiratory. system* 

 

Possible respiratory sensitiser*. 

 

May possibly affect fertility* (limited evidence). 

 

Keep away from combustible material  

 

Avoid exposure - obtain special instructions before use. 

 

To clean the floor and all objects contaminated by this material 
use water and detergent. 

 

Keep away from food drink and animal feeding stuffs. 

 

In case of contact with eyes rinse with plenty term of water and 
contact Doctor or Poisons Information Centre.  

 

If  swallowed  IMMEDIATELY  contact  Doctor  or.  Poisons 
Information Centre (show this container or label). 

 

This material and its container must be disposed of as hazardous 
waste. 

FIRST AID MEASURES

 

SWALLOWED 

 

If swallowed do NOT induce vomiting. 

 

If vomiting occurs, lean patient forward or place on left side (head-down position, if possible) to maintain 
open airway and prevent aspiration.  Observe the patient carefully.

 

 

Never give liquid to a person showing signs of being sleepy or with reduced awareness.

 

 

Give water to rinse out mouth, then provide liquid slowly and as much as casualty can comfortably drink.

 

 

Seek medical advice.

 

EYE 

 

If this product comes in contact with the eyes: 

 

Wash out immediately with fresh running water. 

 

Ensure complete irrigation of the eye. 

 

Seek medical attention without delay; if pain persists or recurs seek medical attention. 

 

Removal of contact lenses after an eye injury should only be undertaken by skilled personnel.

 

SKIN 

 

If skin contact occurs: 

 

Immediately remove all contaminated clothing, including footwear. 

 

Flush skin and hair with running water (and soap if available). 

 

Seek medical attention in event of irritation.

 

INHALED 

 

If dust is inhaled, remove from contaminated area. 

 

Encourage patient to blow nose to ensure clear passage of breathing. 

 

If irritation or discomfort persists, seek medical attention.

 

 

 

Summary of Contents for FP-08450





















Reviews: