background image

 

 

 

 

 

 

Number 

K94463/05 
 

  

 

 

 

 

                    Replaces 

K94463/04 

 

 

 

 

 

 

 

Issued 

January 16

th

,  2017 first issue 

 

 

 

 

 

 

 

Valid until 

December 4

th

,  2019 

 

 

 

 

 

Declaration of Conformity,  
 
based on the requirements § 4.4.2, § 4.4.3 and § 7.15 of                
CEN/TR 15276-1, regarding 

 
FirePro  

Ignition device for Non-Pressurized Condensed Aerosol Generators  

 

 

BTA ignition device (Bulb Thermal Activator) 

 

FPC-5 ignition device in conjunction with 

o

 

Bi-metal switch 

o

 

Heat cable  

o

 

Extension cable for bi-metal switch and heat cable  

 

 

 

 

Kiwa Nederland B.V. 

Sir Winston Churchilllaan 273 

Postbus 70 

2288 AB  Rijswijk 

Tel. +31 88 998 44 00 

www.kiwa.nl 

Executed by: 

Kiwa NCP 

info.ncp@kiwa.nl

 

www.kiwafss.nl 

 

 

Company 

 

 

FirePro Systems Ltd    
8 Faleas Street 
Agios Athanasios Industrial 
Area  
Cy-4041 Limassol - Cyprus 
Tel357 25379999 
Email        

mail@firepro.com

  

Internet     

www.firepro.com

  

 
 
 

 

 

 

 
 
This declaration consists of 6 pages. 
Publication of this declaration is allowed. 
 

Note:  
Publication of only this front page or parts of the declaration is considered as 

not valid

”.

 

 

 

 
 

 
STATEMENT BY KIWA 
With this declaration, Kiwa declares that legitimate confidence exists that 
the products supplied by 
 

FirePro Systems Ltd.  

 
comply with the technical specifications as laid down in this product 
declaration. 
 

 

Ronald Karel 
Kiwa 
 

Summary of Contents for FPC-5V2





















Reviews: