background image

 

 

 

 

DISCLAIMER 

FirePro  Systems  makes  no  representations  or  warranties  of  any  kind,  either  express  or  implied, 

statutory  or  otherwise,  including  but  not  limited  to  warranties  of  merchantability,  fitness  for  a 

particular  purpose,  of  title,  or  of  non-infringement  of  third  party  rights,  including  the  intellectual 

property rights of others. 

 

Any information provided by FirePro Systems, relevant to the system engineering of the project is 

indicative and for guidance purposes only. 

 

ompatible  with  the 

equipment used in the system. Furthermore, the responsibility for the preparation and/ or approval 

of a project, subject to its specifications/ technical features and its related documentation, designs 

or  drawings  adherence  (e.g.  design  documentation,  construction,  as-built  drawings,  circuit 

diagram, cable lengths and voltage drop calculations, etc.) to local, national and international laws 

and  regulations,  falls  entirely  within  the  scope  of  the  contractor/  consultant  assigned  for  the 

installation and commissioning. 

 

 

LIMITATION OF LIABILITY 

In  no  event,  regardless  of  cause,  shall  FirePro  Systems  be  liable  for  any  indirect,  special, 

incidental,  punitive  or  consequential  damages  of  any  kind,  whether  arising  under  breach  of 

contract, tort (including negligence), strict liability or otherwise, even if advised of the possibility of 

such damages. 

NOTE 

FirePro  is  constantly  updating  its  products  and  systems  to  the  state  of  the  art  and  therefore 

reserves  the  right  to  make  changes  in  design,  equipment  and  technology.    You  cannot 

therefore base any claims on the data, illustrations or descriptions contained in this literature. 

 

Summary of Contents for FPC-5V2





















Reviews: