Contact us for assistance: (866) 985-7877 | www.
balkenehome.com
OPERATING INSTRUCTIONS
WARNING
FOR YOUR SAFETY
Be careful when attempting to manually
ignite this heater. Holding in the control
knob for more than 10 seconds before
yÁy¿Ág¿y>¸¿Ñ¿U>ɸg¿>¿L>¿t¿Û>g¿
upon ignition.
LIGHTING
NOTE:
µ¿Á>¿¸Á>µÁ¿µ¿>tÁgµ¿>Ó¿UÓ_gµ¿
U>yg\¿_¿Ág¿UÁµ¿L¿¿tµ¿Ç¿
minutes to purge air from all gas lines
before proceeding.
¿ Ág[¿/¸¿g>Ágµ¿>¸¿
>¿gUÁµU¿yÁ¿>_¿Ñ¿µgªÉµg¿
¸Á>>Á¿t¿¿o¿¿L>ÁÁgµÓ¦¿/g¿
L>ÁÁgµÓ¿¸É_¿Lg¿¸Á>g_¿LÓ¿
ɸUµgÑy¿Ág¿,¿ /,¿ 1//" ¿o¿
L>ÁÁgµÓ¿Á¿UÉ_g_¦
1. Turn the control knob to the “OFF”
position.
2. Fully open the LP cylinder valve.
3. Push in and turn the control knob
to HI.
4. While holding control knob in, push
the RED igniter button to ignite the
main burner.
u¦ /¿_gUµg>¸g¿Ág¿Û>g\¿Áɵ¿Ág¿UÁµ
knob counter clockwise towards LO.
/¿Uµg>¸g¿Ág¿Û>g\¿Áɵ¿Ág¿UÁµ
knob clockwise to HI.
6. To turn the appliance OFF, push in the
control knob and turn clockwise to the
OFF position.
7. Wait at least 5 minutes before
attempting to re-light the heater.
8. Turn the gas cylinder valve to OFF
or closed.
If you experience any ignition
¡µLg¸\¿¡g>¸g¿U¸ÉÁ¿
“Troubleshooting” on page 1
u
.
Caution:
Avoid inhaling fumes
gÁÁg_¿tµ¿Ág¿g>Ágµ²¸¿Úµ¸Á¿É¸g¦¿
Smoke and odor from the burning
of oils used in the manufacturing
will appear. Both smoke and odor
will dissipate after approximately
30 minutes. The heater should
NOT produce thick black smoke.
WHEN HEATER IS ON:
Emitter screen will become bright
red due to intense heat. The color
is more visible at night. Burner will
display tongues of blue and yellow
Û>g¸¦¿/g¸g¿Û>g¸¿¸É_¿Á¿
be yellow or produce thick black
smoke, indicating an obstruction
t¿>µÛÑ¿ÁµÉy¿Ág¿Lɵgµ¸¦¿/g
Û>g¿¸É_¿Lg¿LÉg¿ÑÁ¿¸Áµ>yÁ
yellow tops. If excessive yellow
Û>g¿¸¿_gÁgUÁg_\¿Áɵ¿tt¿g>Ágµ
and consult “Troubleshooting” on
page 1
u
.
RE-LIGHTING:
Note:
¿µ¿Óɵ¿¸>tgÁÓ\¿Ág¿UÁµ¿
L¿U>Á¿Lg¿Áɵg_¿"¿
ÑÁÉÁ¿Úµ¸Á¿_g¡µg¸¸y¿Ág¿
control knob and then rotating
Á¿"¦
1. Turn control knob to OFF.
2. Wait at least 5 minutes to
allow gas to dissipate before
re-lighting.
3. Repeat the “Lighting” steps
listed above.
PUSH &
HOLD
PUSH IN
TURN
PUSHING
IN BUTTON
WHILE
11