background image

 

Safety Precaution 

 

Please observe the following precautions to ensure safe use of equipment.

 

 

1. 

Disconnect the equipment from AC outlet before cleaning.  

Use only moist cloth (with water). Do not use detergent.

 

2. 

Power outlet must be easily accessible and near the equipment. 

3. 

Keep the equipment away from humid and dusty environment.

 

4. 

Place the equipment on a stable surface during installation and operation.

 

5. 

Do not place any load on the power cord.

 

6. 

All cautions and warnings on the equipment should be noted.

 

7. 

When the equipment is not in use, disconnect it from the power source to avoid damage by 

transient over-voltage.

 

8. 

Liquid into the equipment may cause fire or electrical shock.

 

9. 

Only qualified service personnel should be allowed to open the equipment.

 

10.  If any of the following situations arises, ask service personnel to check the equipment:

 

A.  Power cord / plug is damaged 

B.  Liquid penetrates into the equipment

 

C.  The equipment does not function properly and/or cannot work according to the User 

Manual

 

D.  The equipment has been dropped

 

E.  The equipment shows signs of damage 

11.  Temperature below -20° C (-4°F) or above 60° C (140° F) may damage the equipment 

 

 
 
 
 

 

 

 

 

 

 

 

Summary of Contents for AerPPC PP-9635







































Reviews: