background image

 

 

 

 

 

Drive Installation 

There are three steps to install a hard drive or SSD and attach the miniSwap to the computer. The 
dual-bay

 miniSwap/ES

 is shown below to help illustrate the drive install process.  

 

1.  Open the Bay Door 

To open the bay door, slide the latch to the right. 

 

 

 

2.  Insert the HDD or SSD

 

Insert the hard drive with the label facing up and the SATA pins in the rear. The SATA pins 
will be the first part of the device to enter the miniSwap bay. Push the drive in (as far as 
possible) using your thumb until the bay door starts to close.  
 

 

 

WARNING - POTENTIAL DAMAGE 

The SATA pins must be in the correct position to avoid damage.  DO NOT insert a 

PATA device into the miniSwap as this will cause damage not covered by warranty. 

 

 

Carefully press the miniSwap door closed.  The bay is now ready to be used. 

 

Note:

 

This is a critical step. If the fit is too tight, back out the disk and ensure the drive is 

the correct type and positioned properly

.  Do not use excessive force

 when inserting the 

disk.  Excessive force can cause damage to the drive and the enclosure.

 

 

 

To remove a disk, slide the latch to the right and open the door.  Remove the disk as 
shown below. 

Do not use excessive force

 when opening the bay door.  Excessive 

force can cause damage to the enclosure

. If the door will not open easily remove the 

three screws on each side of the enclosure and remove the top to discover the issue. 

 

 

Summary of Contents for miniSwap/U3
















Reviews: