background image

 

16  

Yellow 
tank 
plug 

Filling hose and 
funnel  

Tank Filling and Water Treatment 

Open the rear upper yellow 
tank plug and insert hose 
into tank (rotating the impel-

ler slightly may be necessary to al-
low the hose to pass), move the 
tank adjuster handle to level 20 and 
begin filling.  Do not fill the tank 
higher than the level indicator on the 
front of the clear shell.  A properly 
filled tank holds approximately 
8liters of water. 
   
Warning:  Do not under any circum-
stances put fingers into the tank.  
Use the end of the hose to  
move the impeller should the need 
arise. 

Note:  A large bucket is required for filling (Not included) 

 
In areas where tap water quality is known to be poor, FDF recommends the use of distilled 
water. 

Note: Lower tank plug is permanently 
sealed. 

 

Water Treatment Procedures: 

 

1.  Add Chlorine tablet.   

 

2. Enough Chlorine Tablets are supplied 

for many years of  Water treatment.  
Add a chlorine Tablet whenever the 
Water appears dirty or cloudy.   

 
WARNING:  Only use First Degree  
Fitness Supplied Water treatment tab-
lets.  

 

Use a drop cloth under the tank when 
filling the tank to avoid damage floor or 
carpet 

Caution: 

 

Summary of Contents for fluid e820 Fitness UBE




























Reviews: