background image

ROBO TX ElectroPneumatic

COMPUTING

15

Pinball machine

Now you can play pinball!
Build the model according to the assembly 
 instructions and wire the electrical and pneu-
matic components according to the circuit 
diagram. During assembly pay attention 
to accuracy when installing the parts, 
connecting the hoses and wiring the 
electrical components. This eliminates 
the need for trouble-shooting when you 
put the model into operation.

l

 Before starting to program the model, here is further technical information on the 

cylinder below the model as well as additional actuators and sensors. The cylinder is 
used as a storage reservoir for air, to ensure that enough air is available to move the 
cylinders when the flipper buttons are pressed quickly one after the other. 

l

 The ball can be shot into the playing field by a spring mechanism on the right side of 

the model. This works according to the same principle as a real pinball machine. 
 

l

 The two buttons at the left and right lower 

edges serve for electrical control of the two 
valves for the built-in cylinders. These control the 
two flipper arms. A light barrier detects when a 
ball drops through the middle gap or runs past 
an incorrectly positioned flipper arm. This light 
barrier also serves later for counting the balls 
planned for one game.

l

 Another light barrier and the color sensor serve 

to keep the score .  The light barrier records when 
the ball passes through and the color sensor mea-
sures the distance between the color sensor and 
ball. This is explained in greater detail later in the 
program explanation.

l

 The ROBO TX Controller display serves to 

indicate the score and number of balls remaining. 
The display can be controlled with the two red 
buttons.

Pinball control

Color sensor for proximity measurement

Measured value logging and output

Cylinder as air reservoir

Ball launching pad

Light barrier for detecting passage

Summary of Contents for COMPUTING ROBO TX ElectroPneumatic



















Reviews: